TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel

The TI E2E™ design support forums will undergo maintenance from July 11 to July 13. If you need design support during this time, open a new support request with our customer support center.



Search tips
Showing 20 results View by: Thread Post Sort by
    Answered
  • INA193A-Q1: ina193aqdbvrq1

    Adam S
    Adam S
    Resolved
    Part Number: INA193A-Q1 Tool/software: Hello, question referes to ina193aqdbvrq1 which we are using in our products. according to PCN 20250212005.2, ina193aqdbvrq1 is in the Group 2 and there is a change in Wafer probe site, Assembly /Test site I would…
    • Resolved
    • 3 months ago
    • Amplifiers
    • Amplifiers forum
  • Answered
  • INA193A-Q1: limitation for LPF load

    NOBUO FUJIHARA
    NOBUO FUJIHARA
    Resolved
    Part Number: INA193A-Q1 Other Parts Discussed in Thread: TINA-TI Hi team, INA193A-Q1 datasheet defines 10nF as maximum capacitive load. In case RC LPF is connected to output of INA193A-Q1, is there still restriction for capacitor size? If above is yes…
    • Resolved
    • over 4 years ago
    • Amplifiers
    • Amplifiers forum
  • INA193A-Q1: Common Mode Volatge

    hideyuki sakai
    hideyuki sakai
    TI Thinks Resolved
    Part Number: INA193A-Q1 Dear, Sir. My customer is facing a strange symptom on INA193A-Q1 circuit. Thay are applying 5V for V+(Vs). Rs = 10mOHM. The load is FET(drain). INA193A-Q1 is measuring the current into FET. They set the input floating, so Is…
    • over 5 years ago
    • Amplifiers
    • Amplifiers forum
  • Answered
  • INA193A-Q1: Output Voltage

    Kishore Kumar T M
    Kishore Kumar T M
    Resolved
    Part Number: INA193A-Q1 Other Parts Discussed in Thread: INA193 Hi, As per the output voltage formula in the data sheet , the output voltage should be zero volts when Rs=open & Is =0 Amps, for the same scenario when the model is simulated in TINA TI…
    • Resolved
    • over 5 years ago
    • Amplifiers
    • Amplifiers forum
  • INA193A-Q1: Volatge Output

    hideyuki sakai
    hideyuki sakai
    TI Thinks Resolved
    Part Number: INA193A-Q1 Dear, Sir. My customer is applying INA193A-Q1 for their system, now. They use it under V+=5V, and Rs value is detemined to consider the the peak of normal loading current level & Gain. So, the peak of volatge output is…
    • over 5 years ago
    • Amplifiers
    • Amplifiers forum
  • INA193A-Q1: Output Voltage of amplifier is not having lower saturation as mentioned in Datasheet for Vsense<20mV . We are able to sense less than 0.3V at the Vout corresponding to drop across Shunt.

    Asha Chandrashekar
    Asha Chandrashekar
    TI Thinks Resolved
    Part Number: INA193A-Q1 2 Queries: 1. Output Voltage of amplifier is not having lower saturation as mentioned in Datasheet for Vsense<20mV . We are able to sense less than 0.3V at the Vout corresponding to drop across Shunt. 2. Also , we are able…
    • over 4 years ago
    • Amplifiers
    • Amplifiers forum
  • INA193A-Q1: The clipping output at large input voltage

    Tomoaki Yoshida91
    Tomoaki Yoshida91
    TI Thinks Resolved
    Part Number: INA193A-Q1 Hi team, I have a question about the behavior at large input voltage. We will use normally in the condition that Vsense is under (Vs - 0.2V) / Gain. However, Vsense may exceed this value when the actuator starts up or shuts off…
    • over 5 years ago
    • Amplifiers
    • Amplifiers forum
  • INA193A-Q1: about input bias current

    Paul Kim
    Paul Kim
    TI Thinks Resolved
    Part Number: INA193A-Q1 Hi team INA193A-Q1 D/S say Input bias current = Max 23uA at Vin- pin.. so total input bias current would be Max 46uA(= 23uA x 2) for two input pins ? further, may I know total input bias current for two input pins at Vs = 0V and…
    • over 6 years ago
    • Amplifiers
    • Amplifiers forum
  • Answered
  • INA193A-Q1: INA193A-Q1 Spec question.

    Chun Youngsu
    Chun Youngsu
    Resolved
    Part Number: INA193A-Q1 Hi. During the review of the INA193A-Q1, ask the following questions. I would like to know exactly the Vcm range of 6.3 Recommended Operating Conditions in the Data Sheet. The data sheet is marked with NOM 12V only and needs to…
    • Resolved
    • over 8 years ago
    • Amplifiers
    • Amplifiers forum
  • INA193A-Q1: EMC (DPI method) test result

    Tomoaki Yoshida91
    Tomoaki Yoshida91
    TI Thinks Resolved
    Part Number: INA193A-Q1 HI team, Is there EMC test results by DPI method? Our customer is considering to use INA193A or INA213A. If there already is the test results I would like to obtain it. Both of INA193A-Q1 and INA213A-Q1. Best regards, Tomoaki Yo…
    • over 7 years ago
    • Amplifiers
    • Amplifiers forum
>

Didn't find what you are looking for? Post a new question.

  • Ask a new question