Search tips
Showing 467 results View by: Thread Post Sort by

  • INA240: CURRENT SENSE RANGE

    • Resolved
    Part Number: INA240 Is it possible to measure 150A of current using INA240 ?I need precision shunt

  • INA240: Output impedance, load capability

    TI Thinks Resolved
    Part Number: INA240 I can't find in the datasheet how much load current the amplifier pin 8 output in can handle, or it's internal output impedance. Can only find it's maximum capacitive load is 1nF. Need to know, because the connected sampling...

  • INA240: TINA Simulation Result

    • Resolved
    Part Number: INA240 Hi Sir/Madam, I think the input is sinusoidal waveform to simulate three-phase

  • INA240: Unbalanced midsupply voltage

    Part Number: INA240 Hello, I created a current sensing circuit with INA240A1D recently. The electronic circuit is below. I set the output to be midsupply voltage, but the wrong voltage is outputted. Vcc = 5.0 [V] (IN+) - (IN-) = 0.0[mV] Out = 1.53...

  • INA240: INA240: Current Measurement Range

    • Resolved
    Part Number: INA240 Hello, So in order to prevent the output from saturating, the equation VOUT

  • INA240: Current Measurement Range

    • Resolved
    Part Number: INA240 Hello, I was not successful determining the measurement range for the INA240

  • INA240: About Low noise current amplifier

    TI Thinks Resolved
    Part Number: INA240 Hi I'm looking for a low noise current amplifier. The current detection data will be captured by the ADC in a 200kHz cycle. Therefore, we think that our requirement is that the characteristics of CMRR are good at 200kHz....

  • INA240: current sense resistor - trace length

    • Resolved
    Part Number: INA240 Dear TI Amps Team, my customer was reading the layouts recommendations

  • INA240: Inputs biased when unpowered?

    TI Thinks Resolved
    Part Number: INA240 Is there any risk in having voltage applied to inputs when the device is unpowered? I don't see the presence of input clamp structures in the datasheet.

  • INA240: Settling time

    TI Thinks Resolved
    Part Number: INA240 Please explain the discrepancy between the INA240 settling time differences seen when comparing figure 21 and figure 37 in INA240 datasheet...? Figure 21 indicates 90V step settle in < 2uS but figure 37 shows 24V step settle time...

Didn't find what you are looking for? Post a new question.


All content and materials on this site are provided "as is". TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with regard to these materials, including but not limited to all implied warranties and conditions of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. No license, either express or implied, by estoppel or otherwise, is granted by TI. Use of the information on this site may require a license from a third party, or a license from TI.

Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Terms of use of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Terms of use of this site. TI, its suppliers and providers of content reserve the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.

TI worldwide | Contact us | myTI login | Corporate citizenship

TI is a global semiconductor design and manufacturing company. Innovate with 100,000+ analog ICs and
embedded processors, along with software, tools and the industry’s largest sales/support staff.

© Copyright 1995-2021 Texas Instruments Incorporated. All rights reserved.
Trademarks | Privacy policy | Terms of use