The TI E2E™ design support forums will undergo maintenance from July 11 to July 13. If you need design support during this time, open a new support request with our customer support center.



Search tips
Showing 144 results View by: Thread Post Sort by

  • INA260: motor jitters when using your part

    TI Thinks Resolved
    Part Number: INA260 Other Parts Discussed in Thread: INA240 Tool/software: Hi, My motor jitters when using INA260 to measure its Current. Does your part work in PWM ? My motor is 24VDC, driven by PWM between 10% and 100%, and its current (in test mode…

  • INA260: VBUS pin blowing up on chips

    Part Number: INA260 Tool/software: Hello, We have a fairly simple circuit for monitoring 3 dc voltages with 3 INA260's and a raspberry RP2040 microcontroller. The dc voltages are 24v batteries. The INA is powered using a 2405 TracoPower regulator…

  • INA260: ALERT Pin Behavior During I2C Access

    TI Thinks Resolved
    Part Number: INA260 Tool/software: Hi, I would like to confirm something about the INA260 ALERT pin. Does the ALERT pin toggle between high and low during I2C access? I was wondering about this after looking at Figure 27 in the datasheet. The toggling…
    • Answered

  • INA260: INA260 mid-side monitor ?

    Resolved
    Part Number: INA260 Other Parts Discussed in Thread: INA240 Hello, I built a current source and used INA260 to measure current. The INA260 is placed between load and FET's, so neither IN+ is on VCC, neither IN- on GND. My measurement are different then…
    • Resolved

  • TI-SCB: Does the TI_SCB work with the INA260 Modules ?

    TI Thinks Resolved
    Part Number: TI-SCB Other Parts Discussed in Thread: INA260EVM , INA260 Tool/software: Im trying to test a INA260EVM, I have the TI-SCB connected to it but it is not getting recognized in the EVM software.

  • RE: INA260: request for schematic review.

    Hi Sang, The absolute maximum of the device is 40V, while the device is spec'd from 0-36V. We do not recommend exceeding 36V as the results would not be as predictable. If you were to use over 36V, it would not break until you reach 40V. Best, Mo…

  • INA260: current offset meaning

    TI Thinks Resolved
    Part Number: INA260 Hello expert, My customer has one question about current offset. In our experience, offset is related to LSB with voltage level. May we know the meaning of current offset in INA260 datasheet figure 2? Thanks a lot! Best regards, Ann…
    • Answered

  • INA260: Common-mode input voltage

    Resolved
    Part Number: INA260 Other Parts Discussed in Thread: INA236 , INA232 Hello. In my application, the power output from a solar panel is to be measured with an INA260. The problem here is that the common mode voltage limits of the INA260 must be observed. The…
    • Resolved

  • INA260: INA260 I2C address not responding to mapped address

    TI Thinks Resolved
    Part Number: INA260 We are using INA260AIPWR in our design , with following configuration. We had produced 3K units with out any issues Everything was working fine with address 80 81 & 8A & 8B. In our recent batch production 80 address we are…
    • Answered

  • INA260: Is the power register value really calculated from the current and voltage register values?

    Resolved
    Part Number: INA260 Hello. There is an interesting phenomenon in the power calculation of the INA260, which I do not understand: In a simple test setup, I measure the current through a power resistor simultaneously with 4 INA260's, connected in series…
    • Resolved

Didn't find what you are looking for? Post a new question.