Search tips
Showing 179 results View by: Thread Post Sort by

  • INA282: With load current increase, the output of INA282 oscillates in wide range

    Part Number: INA282 HI Team, INA282 is used to monitor negative voltage -6.5V in our design. Refer to the snap below.. On board measured output voltage of INA282 varies too much at 1.86A. Output variation is as shown below (2.808 to 2.935…

  • INA282-Q1: Output(pin 5) of Amplifier struct at 10.54mV

    TI Thinks Resolved
    Part Number: INA282-Q1 In my case Using INA282AIDGKT for Over Current Protection for power rail 6.5V, 2A(limited). When i tried to test the circuit i increased the current more than 2A, output of Amp struct at 10.54mV. Could you please advise if the…

  • INA282-Q1: INA282-Q1:

    TI Thinks Resolved
    Part Number: INA282-Q1 Other Parts Discussed in Thread: ADS1118 Hello, We are using external ADC (ADS1118IDGSR) . for current sensing by IC INA282-Q1. We have connected shunt resister of value 0.0001ohm(connected 0.0003ohm in parallel manner) at high…
    • Answered

  • INA282: p2p solution to INA282AIDR

    Resolved
    Part Number: INA282 Other Parts Discussed in Thread: INA240 , Hi Current Sensing Folks, Does TI have p2p device for INA282AIDR? Otherwise, could you help suggest any similar device even though it's not p2p? Thank you.
    • Resolved

  • INA282: INA282 for battery test equipment

    TI Thinks Resolved
    Part Number: INA282 Hi, customer use INA282 with VSSOP package in high precision battery test equipment,and have a problem about the output voltage. the schematic as below, current sense resistor is 0.01ohm. During the battery charge and discharge…
    • Answered

  • INA282: Current Sensing circuit ,Accuracy 1mA

    Resolved
    Part Number: INA282 Other Parts Discussed in Thread: INA210 , INA302 , INA240 , INA190 Hello, I am Using current INA282 Current sensor (Bi-Direction). My Current range is from 100mA to 13.5A in one direction and in another direction the Current range…
    • Resolved

  • INA282: INA282 Equation questions.

    TI Thinks Resolved
    Part Number: INA282 Hi support team experts, My customer is having some urgent question regarding the equations in the INA282 datasheet, could you please help us to clarify them: System Setting: REF1 => 0V (Grounded) REF => 2.495V (from…
    • Answered

  • INA282: Question on BW of Current Sensor

    Resolved
    Part Number: INA282 Other Parts Discussed in Thread: INA201 , INA193 , INA226 , INA220 Hi team, I have questions on BW of current sensor. 1. INA282 has 10kHz of BW, which is quite narrow when it's compared to other INA parts such as INA193 and INA201…
    • Resolved

  • INA282: common mode voltage question

    TI Thinks Resolved
    Part Number: INA282 Other Parts Discussed in Thread: INA283 Hello, I am using the INA282 in a new design. I inserted a schematic showing how I am using this part in the design. The bus supply is 15.7 VDC. The nominal power draw to the "Trillium_Power…

  • INA282: Measuring 8mV at output with REF's grounded and no current through shunt

    TI Thinks Resolved
    Part Number: INA282 Other Parts Discussed in Thread: LM7705 Below is the circuit I'm trying to test. Without a load I'm measuring 8mV at the output. I've built 6 copies of this circuit and all behave the same. In 2 instances I measured 0V at the output…

Didn't find what you are looking for? Post a new question.