Search tips
Showing 23 results View by: Thread Post Sort by

  • INA282-Q1: Output(pin 5) of Amplifier struct at 10.54mV

    TI Thinks Resolved
    Part Number: INA282-Q1 In my case Using INA282AIDGKT for Over Current Protection for power rail 6.5V, 2A(limited). When i tried to test the circuit i increased the current more than 2A, output of Amp struct at 10.54mV. Could you please advise if the chip…

  • INA282-Q1: INA282-Q1:

    TI Thinks Resolved
    Part Number: INA282-Q1 Other Parts Discussed in Thread: ADS1118 Hello, We are using external ADC (ADS1118IDGSR) . for current sensing by IC INA282-Q1. We have connected shunt resister of value 0.0001ohm(connected 0.0003ohm in parallel manner) at high side…

  • INA282-Q1: response time

    TI Thinks Resolved
    Part Number: INA282-Q1 Hi I have some question about the response time. I found some data on the datasheet such as Fig 31. What is the "input Drive" ? Is that a differential voltage of IN+ and IN-? Or is that VCM voltage? I would like to know…

  • INA282-Q1: about input bias current

    TI Thinks Resolved
    Part Number: INA282-Q1 Hi team INA282-Q1 D/S say Input bias current = TYP 25uA per pin. so total input bias current would be TYP 50uA(= 25uA x 2) for two input pins ? further, may I know total input bias current for two input pins at Vs = 0V and common…
    • Answered

  • RE: INA282-Q1: Product information related with Lifecycle

    Resolved
    Hi, The INA282-Q1 has not EOL schedule.
    • Answered

  • INA240-Q1: Questions regarding replace INA282 by INA240

    Resolved
    Part Number: INA240-Q1 Other Parts Discussed in Thread: INA282 , INA240 Hi team, My customer wishes to replace INA282 by INA240 and have few questions regarding the datasheet spec, could you please help to clarify the following questions: 1. Is it okay…
    • Resolved

  • INA282-Q1: Proper connection and setup for low-side measurement

    TI Thinks Resolved
    Part Number: INA282-Q1 Other Parts Discussed in Thread: INA282 , INA210-Q1 , INA199-Q1 , INA301 , INA180 Dear*, I want to measure current from 0A to 20A on the low-side. 1) What is the proper connection of INA282 REF1 and REF2 pins if: - I have a 3.3V…

  • INA282-Q1: How to improle for BCI

    TI Thinks Resolved
    Part Number: INA282-Q1 Other Parts Discussed in Thread: INA282 Hi, Our customer has a issue for Bulk Current Injection test. They are considering countermeasures. #1 They insert condenser each input pin to GND and differential for input noise. They are…
    • Answered

  • INA282-Q1 Input Filter

    Resolved
    Other Parts Discussed in Thread: INA282-Q1 , INA210-Q1 Hello, Customer is considering to use INA282-Q1. Please answer following question from customer. INA282-Q1 datasheet page 14 has following explanation. “Despite the use of internal zener-type electrostatic…
    • Resolved

  • INA286: INA286 output noise issue

    TI Thinks Resolved
    Part Number: INA286 Other Parts Discussed in Thread: INA282 , INA293 Hi, Support Team 1. The load is an electronic load with CC mode and we have also applied a CV on Shunt-Resistor to generate a DC current (all PWMs and Power Stage are stop), the output…

Didn't find what you are looking for? Post a new question.