Search tips
Showing 31 results View by: Thread Post Sort by

  • INA296B-Q1: INA296B4Q - Gain Error Factor

    TI Thinks Resolved
    Other Parts Discussed in Thread: INA240 Tool/software: Hi, Based on the feedback from e2e forum for the query, " INA296B4Q - Gain Error Factor ", To calculate the gain error factor for the use case of an external series filter resistor (Rs),…

  • INA296B-Q1: Input resistance value shown in the block diagram

    TI Thinks Resolved
    Part Number: INA296B-Q1 Tool/software: Hi, What is the resistance value (marked in the image below) of the INA296x part? Regards, Devendhiran K
    • Answered

  • INA296B: About Accuracy

    Resolved
    Part Number: INA296B Other Parts Discussed in Thread: INA296A Tool/software: Hello, Thank you for your help. We are designing the attached current sense circuit using INA296B5. The accuracy of low currents of 1A to 20A may exceed ±2%. Is there any…
    • Resolved

  • INA296B: Standby

    TI Thinks Resolved
    Part Number: INA296B Tool/software: Hey, I like to use the current sense for <60V high side bidirectional current sensing of a DC/DC unit and have several of them in multiple in- and outputs. All active the suppy current of them in sum is very high…

  • INA296B-Q1: RCM & RDIFF values

    TI Thinks Resolved
    Part Number: INA296B-Q1 Other Parts Discussed in Thread: INA310A-Q1 Tool/software: What is the Common mode Impedance (RCM) and Differential mode Impedance (RDIFF) values of INA310A-Q1 device?

  • INA296B-Q1: Use case of high value of series resistor at input path

    TI Thinks Resolved
    Part Number: INA296B-Q1 Tool/software: We need to monitor the current through a Shunt resistance of 40mOhm. For the diagnostic purpose, we are planning to keep 1K ohm resistor in series between the IN+ & IN- pins and the shunt resistor. So now the…
    • Answered

  • INA296B-Q1: RVRR (Reference voltage rejection ratio) specification

    Resolved
    Part Number: INA296B-Q1 Other Parts Discussed in Thread: INA296B TI Team, Cusotmer calculates worst case error for INA296B-Q1 output. In the datasheet a RVRR (Reference voltage rejection ratio, input referred) parameter is specified for the case when Vref1…
    • Resolved
    • Answered

  • INA296B-Q1: Output Set Using Resistor Divider

    Resolved
    Part Number: INA296B-Q1 Hello team, In the D/S of INA296B-Q1, there are below statement highlighted in yellow. Could you explain more clearly why TI doesn't recommend a single-ended measurement with this configuration? 1. Regards, Hirata
    • Resolved

  • INA296B: Find a another solution to attack TPA1295

    TI Thinks Resolved
    Part Number: INA296B Other Parts Discussed in Thread: INA240 Hi, Now my customer want to use a precision Amps in the high side of DC/DC part. And their demands are 3.3V supply voltage , common voltage over 25V, bandwidth over 500KHz, and max bidirectional…
    • Answered

  • INA296B: INA296B3 has a gain of 60V/V instate of 50V/V

    Resolved
    Part Number: INA296B I use an INA296B3 to sense an high side over current according the following circuit: The measurements with a static current of +20A through the shunt resistor cause an input voltage differential of +10mV (IN+ to IN-). The voltage…
    • Resolved

Didn't find what you are looking for? Post a new question.