• 

  Neal Zhu

  • 2 months ago
  • Amplifiers
  • Amplifiers forum

  INA300-Q1: Over current threshold

  TI Thinks Resolved

  Part Number: INA300-Q1 Hi, I would like to ask some questions about the overcurrent threshold. 1. What is the default value of the over-current threshold at the first power on? Is it judged to be over-current when the power is on? 2. Over-current...
• 

  Jonathan Geronga

  • 3 months ago
  • Amplifiers
  • Amplifiers forum

  INA300-Q1: 28A to 30 A overcurrent protection device

  • Resolved

  Part Number: INA300 - Q1 Hi Team, Our customer is looking for a 28 A to 30 A overcurrent protection
• 

  Patrick Simmons

  • over 1 year ago
  • Amplifiers
  • Amplifiers forum

  RE: INA300-Q1: INA300-Q1

  Hello Samet, As per your message above you acknowledge that our model works in our platform and has issues in our competitor's platform, ltspice. As such I am closing this thread. However, I have reached out to you for continued support outside...
• 

  Forrest Smith

  • over 2 years ago
  • Amplifiers
  • Amplifiers forum

  INA300-Q1: low-pass filtering inputs to INA300-Q1

  Part Number: INA300-Q1 I am applying the OCP chip with a 28V high-side source and a 10 milli-ohm shunt. - if I am implementing the low-pass input filtering scheme from Figure 30 of the data sheet, is there a limitation on the value of CFILTER? I am...
• 

  PRIYA BAGAL

  • over 2 years ago
  • Amplifiers
  • Amplifiers forum

  INA300-Q1: Overcurrent not detected

  • Resolved

  Part Number: INA300 - Q1 Hello, I have selected this part for Battery management cicuit
• 

  Adam Berger

  • 9 months ago
  • Power management
  • Power management forum

  TPS1HB08-Q1: Confusion about t_OFF parameter in family

  • Resolved

  " current limit across multiple subsystems using an INA300 - Q1 , with an \ALERT from the INA300 pulling down
• 

  Paul Kim

  • over 2 years ago
  • Amplifiers
  • Amplifiers forum

  INA300-Q1: about input bias current

  TI Thinks Resolved

  Part Number: INA300-Q1 Hi team INA300-Q1 D/S say Input bias current = Max 0.5uA for disable mode. so total input bias current would be Max 1uA(= 0.5uA x 2) for two input pins ? further, I have to double the graphed Ib on Figure 8(Disabled) for...
• 

  Patrick Simmons

  • over 2 years ago
  • Amplifiers
  • Amplifiers forum

  RE: INA300-Q1: Alert signal does not go low when we added switch and control circuit

  Hello Priya, Were you able to check any of the items I mentioned in my last post?
• 

  Ben Huang1

  • over 3 years ago
  • Amplifiers
  • Amplifiers forum

  INA300-Q1: Is low current detection feasible?

  Part Number: INA300-Q1 Hi Sir INA300-Q1 is for Over Current Protection. We would like to implement the similar function but low current detection Load current of 5mA flow through RSENSE = 10mohm The differential voltage = 50uV Does...
• 

  Andrew Sharp2

  • over 3 years ago
  • Amplifiers
  • Amplifiers forum

  RE: INA300-Q1: ALERT output latching in transparent mode

  Hi Carolus, Thought I'd check in again for this item. Regards, - Andrew

Didn't find what you are looking for? Post a new question.

• Ask a new question