Search tips
Showing 11 results View by: Thread Post Sort by

  • INA337: INA337 with single ended input

    TI Thinks Resolved
    Part Number: INA337 Tool/software: Hello Sir, I want to use INA337 instrumentation amplifier with single ended input and 0.75 Gain with 5V single supply. Do you think it cause anything wrong if I connect + channel single ended input(sensor single…

  • INA337: INA337AIDGKT

    Answer Suggested
    Part Number: INA337 Tool/software: Hi there, Could you inform me about terminal finish of the part INA337AIDGKT. Could you tell me the thickness of Au in case terminal finish is NiPdAu or Au or NiAu. Could you tell me Moisture Sensitivity Level (MSL…

  • INA337: INA337 going to saturation

    TI Thinks Resolved
    Part Number: INA337 Other Parts Discussed in Thread: LMV321 , INA321 Hai, I am using INA337 instrumentational amplifier with gain of 1 for reading a high voltage 405V signal with resistor divider network as per the attached schematic. I have added a…
    • Answered

  • INA337: Amplifying Load Cell Signal

    Resolved
    Part Number: INA337 Other Parts Discussed in Thread: INA326 , Hi, I am amplifying a tension and compression strain gauge type load cell with the INA 337, but I am running into issues. Two issues I am having. 1. I am unable to provide the load…
    • Resolved
    • Answered

  • INA337: INA337 output information

    Resolved
    Part Number: INA337 Other Parts Discussed in Thread: INA326 Hi team customer want to know that use INA337 when 0.125 times gain, Vin = -10V, what is Vout value？ is -1.25V? Best regards Aosker Lau
    • Resolved
    • Answered

  • INA337: INA-CMV-CALC

    Resolved
    Part Number: INA337 There is no INA337 in the parts list in INA-CMV-CALC. How can I add the component?
    • Resolved

  • INA337: INA337, current detection circuit, when the input is 0V, the output end is always 64mV potential, and the 7 pin is still 58mV when it is connected to USB VCC. However, this potential is not fixed superimposed, and gradually decreases with the...

    Part Number: INA337 INA337, current detection circuit, when the input is 0V, the output end is always 64mV potential, and the 7 pin is still 58mV when it is connected to USB VCC. However, this potential is not fixed superimposed, and gradually decreases…

  • INA337 Expected Performance

    Other Parts Discussed in Thread: INA337 With a condition where there is no connection (open inputs) to pins 2 & 3 of the subject amplifier in a single-supply operation application, what is the expected output? Is the output expected to go to high rail…
    • Answered

  • INA321: Output noise problem

    Resolved
    Part Number: INA321 Other Parts Discussed in Thread: INA337 Hi everybody, For a load cell amplification I'm using the INA321 with a gain of 500. Following datasheet, I've set R2 = 99 kOhm and R1 = 1 kOhm. Reference is set to GND and voltage supply is…
    • Resolved
    • Answered

  • INA338: SPICE model required

    Resolved
    Part Number: INA338 Other Parts Discussed in Thread: INA326 , ADS131M06 , INA333 , INA337 Hello, I have some uncertainty regarding INA338 instrumentation amplifier. Is there some verified SPICE model? I would like to simulate my circuit, to find confidence…
    • Resolved

Didn't find what you are looking for? Post a new question.