Search tips
Showing 26 results View by: Thread Post Sort by

  • INA350: INA350

    TI Thinks Resolved
    Part Number: INA350 Other Parts Discussed in Thread: INA351 , TLV9041 Tool/software: Hello TI Team, We intend to use INA350 to interface the thermocouple. So could you please suggest the design ? ---------- Regards Keyur Parikh

  • INA350:INA350CDSIRUGR

    Part Number: INA350 Tool/software: The title of the INA350 datasheet states that the power supply voltage is 1.8V to 5.5V, but page 8 states that it is 1.7V to 5.5V. From what voltage to what voltage can operation be guaranteed?

  • INA350: in

    Part Number: INA350 Tool/software: Hello, Suggested design does not wirk as a required with INA350. Could you please check and let me know further solution.

  • INA350: INA350 saturated output

    TI Thinks Resolved
    Part Number: INA350 Hi everyone, I have a problem with INA350CDS. I'm trying to read the temperature from a PT1000, connected to a Wheatstone bridge. I powerised the instrumental amplifier at 3V3, but the output resultan gets saturated around 0,6V no…
    • Answered

  • INA350: Inconsistent gain over output range

    Resolved
    Part Number: INA350 Other Parts Discussed in Thread: LM358 Tool/software: Hi! I'm having some major gain issues with the INA350AB. The circuit is an (supposed to be precision) ohmmeter for 1~30 ohms. U11 is a LM358 or equivalent. The circuit is…
    • Resolved

  • INA350: Can I reduce offset by software?

    Part Number: INA350 Other Parts Discussed in Thread: INA351 Tool/software: When REF connect to GND, this circuit output 8.86mV. When REF connect to 1.65V, this circuit output 1.65V. Why does different REF get different offset? When REF=1…
    • Answered

  • INA350: INA350

    Resolved
    Part Number: INA350 Other Parts Discussed in Thread: RCV420 Hi , I am trying to measure min current - 4mA max current - 20mA four wire 4-20 current loop Vcm-12V Vs=3.3V. The part I would like to use is INA350 Just would like to know if it…
    • Resolved
    • Answered

  • INA350: Suggestions for level-shifting GS pin for bipolar supply

    Resolved
    Part Number: INA350 Other Parts Discussed in Thread: TL331B Tool/software: Hello, I'm using the INA350 with a bipolar +/- 2.75V supply but trying to control the GS pin using a 3.3V GPIO. It seems that to achieve logic-low I need to drive GS below -2.55V…
    • Resolved
    • Answered

  • INA350: Input Resistors Kill Gain in Unipolar Configuration

    Resolved
    Part Number: INA350 Other Parts Discussed in Thread: TINA-TI , INA351 Tool/software: Please find attached a small TINA-TI simulation of INA350. When the two input resistors are each 200kOhm, the gain gets killed down to 0dB. When I change to 0ohm, the…
    • Resolved
    • Answered

  • INA350: Converting 50mV to 500mV to 0V to 5 V.

    Resolved
    Part Number: INA350 Other Parts Discussed in Thread: TL431 , TLV9061 Tool/software: I have a sensor with an output range of 50mV to 500mV relative to ground. I need to convert this signal to a 0-5V range (or another suitable range) for measurement with…
    • Resolved

Didn't find what you are looking for? Post a new question.