• ISO120: Spice module for ISO120/ISO121

  

  MANOJ S K

  TI Thinks Resolved

  Part Number: ISO120 Other Parts Discussed in Thread: ISO224 , , ISO121 Tool/software: Dear Team, We are looking for Spice module for simulating ISO120xx / ISO121xx in TINA software. Therefore anyone provide suggestions for the same. Note: I already…

  • 4 months ago
  • Amplifiers
  • Amplifiers forum

• ISO121: ISO121G, Assembly site code for ALP= 8

  

  Kevin Korn

  Part Number: ISO121 Other Parts Discussed in Thread: ALP Tool/software: Hello, We have some inventory from year 2008 date codes and need assistance deciphering the assembly site. Please see attached photo, we believe the last 8 on the second line of the…

  • 6 months ago
  • Amplifiers
  • Amplifiers forum
Answered

• ISO121: ISO121 layout

  

  Jesse Zhou

  Resolved

  Part Number: ISO121 Hi, guys, I got a question about the PCB layout of the isolation amplifier ISO121, I place ISO121 on PCB top layer, can I route traces on top layer under ISO121? Thanks !

  • Resolved

  • over 2 years ago
  • Amplifiers
  • Amplifiers forum
Answered

• ISO121: Power Supply ISO121BG

  

  MASSIMO FIORI

  Resolved

  Part Number: ISO121 Other Parts Discussed in Thread: ISO224 Good morning, I don't find information about power dissipation of ISO121BG in datasheet , could you help me ? I asked it because I don't know how select tantalium capacitor for power supply …

  • Resolved

  • over 4 years ago
  • Amplifiers
  • Amplifiers forum

• ISO121: Correct temperature: -55 to +125 or -20 to +85

  

  KS Rajath

  TI Thinks Resolved

  Part Number: ISO121 What is the correct operating temperature of ISO121BG? In datasheet it says -20 to +85 and also -55 to +125, which one is correct?

  • over 4 years ago
  • Amplifiers
  • Amplifiers forum
Answered

• ISO121: ISO121 Single power supply

  

  Clifton Chey

  Resolved

  Part Number: ISO121 Other Parts Discussed in Thread: AMC1300 , AMC1301 Hi, My applicaiton is to measure a current-source (200nA to 10uA) of 50ohm, and the Isolation is to be 3KV and above. I have selected ISO121 as an Isolation Amplifier for the rated…

  • Resolved

  • over 7 years ago
  • Amplifiers
  • Amplifiers forum

• ISO121: Applying INPUT signal to the output of ISO121 IC

  

  Sivakumar Shanmugam

  TI Thinks Resolved

  Part Number: ISO121 Other Parts Discussed in Thread: ISO224 Hi, We are using ISO121BG for one of our Isolation requirement. Per the design requirement, we are in need to apply 10V DC input to the VOUT (pin 18) of IC ISO121BG continuously while there…

  • over 7 years ago
  • Amplifiers
  • Amplifiers forum

• ISO121: Code at the bottom of the part number

  

  Danilo A.

  TI Thinks Resolved

  Part Number: ISO121 Hi Team, A customer noticed a code at the bottom of the part number of ISO121G and would like to know the significance of that code. Here is the picture of the device. Regards, Danilo

  • over 5 years ago
  • Amplifiers
  • Amplifiers forum
Answered

• ISO121: PSPICE Model Netlist Errors with PSPICE for TI

  

  Vaishnav Achath

  Resolved

  Part Number: ISO121 Other Parts Discussed in Thread: ISO224 , ISO120 , PSPICE for TI comes with ISO121X Model and when using it to simulate a simple application circuit, it results in several netlisting errors as shown below and simulation does not run…

  • Resolved

  • over 4 years ago
  • Amplifiers
  • Amplifiers forum
Answered

• ISO121: Is this rated for 4950 Vdc for continuous use?

  

  Noriyuki Takahashi

  Resolved

  Part Number: ISO121 Hi team, It looks like ISO121 is rated for 4950 Vdc for continuous use. Is this correct? And is there an evaluation board available for the ISO121? Regards, Noriyuki Takahashi

  • Resolved

  • over 6 years ago
  • Amplifiers
  • Amplifiers forum

Didn't find what you are looking for? Post a new question.