Search tips
Showing 24 results View by: Thread Post Sort by
    Answered

  • LF411: Simulation based on SBOA436

    Resolved
    Part Number: LF411 Other Parts Discussed in Thread: TL071H , TL081H Hello team, My customer is simulating a circuit based on SBOA436( https://www.ti.com/lit/an/sboa436/sboa436.pdf ). In the simulation, we obtained an output clip of current and voltage. I…
    • Resolved
    • Answered

  • LF411: BAL pins unconnected

    Resolved
    Part Number: LF411 Hi all, I need to use the LF411 amplifier for a project (i.e. replacing it is not possible). I could not find much information about the balance pins (i.e. pins 1 and 5). If it is not necessary to trim the input offset voltage, is it…
    • Resolved
    • Answered

  • THS3092: Running transient response in TIna against an LF411 and getting same results

    Resolved
    Part Number: THS3092 Other Parts Discussed in Thread: LF411 , TINA-TI , THS3091 shown is tina schematic with LF411 and THS3092 with identical circuits. VG2 is 3nS rise/fall 40MHz waveform. Looks more ideal on both than realistic. Only expected response…
    • Resolved
    • Answered

  • LF411: TINA: LF411: Operating point not found

    Resolved
    Part Number: LF411 Other Parts Discussed in Thread: TINA-TI Hello there I have an error in TINA software-related Operating point not found, I have seen other posts related to this error, I have tried on transient analysis too (tried all 3 options: calculate…
    • Resolved

  • LF411: Is LF411CP cross-ref for obsolete LF411CN?

    TI Thinks Resolved
    Part Number: LF411 Trying to determine if LF411CP is equiv. replacement for obsolete LF411CN (IC OPAMP JFET 1 CIRCUIT 8DIP).

  • LF411: design parameters for BAL 1 and BAL2 pins

    TI Thinks Resolved
    Part Number: LF411 Hello Team, Good day. My customer is looking for design parameters for BAL1 and BAL2 pins for the LF411 device. The datasheet has limited information on these pins, can you share any information we can use? Regards, Renan
    • Answered

  • LF411: Resistance of pin 1 and pin 5

    Resolved
    Part Number: LF411 Hi Team, Previously purchased LF411CN, the resistance pin 1 and pin 5 is 24KΩ. Then replaced LF411CN with LF411CP, and the resistance of pin 1 and pin 5 is 2KΩ. It is reasonable to say that the resistance of alternative part will not…
    • Resolved

  • LF411: Equivalent input noise voltage

    TI Thinks Resolved
    Part Number: LF411 Hi E2E, Good day. The LF411CP is the suggested replacement for the obsolete device LF411CN/NOPB. From the LF411CN/NOPB datasheet, the equivalent input noise voltage is typically 25 nV / √Hz where the test condition is f=1 kHz Rs=100…
    • Answered

  • LF411: About the specification of LF411CN and LF411CP

    Resolved
    Part Number: LF411 Hi Team, Please help me answer the follow question from my customer, thank you so much. We can't find the term of source current and sink current of those products. Also we can't find the term of voltage gain. Please let us know…
    • Resolved

  • LF411: The junction temperature(Tj) on LF411CP

    TI Thinks Resolved
    Part Number: LF411 Hello, Regarding to junction temperature on LF411CP, my customer is asking a question. They will use LF411CP for replacement of LF411CN/NOPB(End of life). (Question) Could you please tell us junction temperature(Tj) on LF411CP? It…

Didn't find what you are looking for? Post a new question.