• LM239A-EP: Parts ESD in Human Body Model (HBM) classification

  

  Noah Burgio

  TI Thinks Resolved

  Part Number: LM239A-EP Other Parts Discussed in Thread: OPA347 , SN74AHCT1G14 , TLE2021-EP , TPS3809-EP , TLV2371 , Tool/software: To whom this may concern, I was wondering what the ESD rating is in terms of Human Body Model (HBM) classification of…

  • 4 months ago
  • Amplifiers
  • Amplifiers forum
Answered

• LM239A-EP: ESD Ratings

  

  Andy Pilling

  Resolved

  Part Number: LM239A-EP Other Parts Discussed in Thread: LM239A Hi, There are no figures for the ESD ratings in the LM239A-EP datasheet. Please can you let me know the figures for HBM and CDM? Thanks Andy

  • Resolved

  • over 2 years ago
  • Amplifiers
  • Amplifiers forum

• LM239A-EP: Current consumption

  

  Ravi Patel

  TI Thinks Resolved

  Part Number: LM239A-EP It has been mentioned in the datasheet the total supply current requirement for whole IC is 2 mA. However, the specification for low-level output current (which is 16 mA typical) is not mentioned clearly that whether it is for single…

  • over 3 years ago
  • Amplifiers
  • Amplifiers forum
Answered

• LM239A: LM239A do not exceed -.3V on input pins

  

  Jason Smith1

  Resolved

  Part Number: LM239A Other Parts Discussed in Thread: LM339 If noise spikes are exceeding -.3V on the input pins, is there risk of damage to the product?

  • Resolved

  • over 5 years ago
  • Amplifiers
  • Amplifiers forum
Answered

• RE: LM239A: LM239A

  

  Paul Grohe

  Resolved

  Hello, The input voltage cannot go more than 300mV below the GND pin. So if the GND pin is at Ground, then the input voltage cannot go lower than -0.300V.

  • over 7 years ago
  • Amplifiers
  • Amplifiers forum

• LM239A: Common mode input voltage query

  

  Art Mecina

  TI Thinks Resolved

  Part Number: LM239A Other Parts Discussed in Thread: LM339 Hello Guys, Good day. The common mode input voltage range states that the input voltage can go up to Vcc-2V, I'm assuming this means for both inputs per comparator and therefore one input…

  • over 4 years ago
  • Amplifiers
  • Amplifiers forum

• LM239A-Q1: Difference between LM239AQDRG4Q1 and LM239AQDRQ1

  

  Jessica Wu74

  TI Thinks Resolved

  Part Number: LM239A-Q1 Hi Team, Could you please kindly help to confirm what is the difference between LM239AQDRG4Q1 and LM239AQDRQ1? Thank you very much for your support. Best regards Jie

  • over 4 years ago
  • Amplifiers
  • Amplifiers forum

• LM239A: We cannot process your order at this time due to corporate policy restriction CP2

  

  Tommy Chen

  TI Thinks Resolved

  Part Number: LM239A I want to order LM239AQDRQ1 which show in stk, but it warned "We cannot process your order at this time due to corporate policy restriction CP2". What does this mean? How to solve? Thank you.

  • over 4 years ago
  • Amplifiers
  • Amplifiers forum
Answered

• LM239A-EP: Tie the open drain output through pull-up resistor to a voltage while the device is unpowered

  

  Xiang Maverick

  Resolved

  Part Number: LM239A-EP If the device is unpowered, Can I tie the open drain output through pull-up resistor to a voltage (for example 1.8V). Would the device be powered through the output pin?

  • Resolved

  • over 3 years ago
  • Amplifiers
  • Amplifiers forum
Answered

• LM239A-EP: How to terminate an unused comparator

  

  Paul Marchese

  Resolved

  Part Number: LM239A-EP Dear TI, I'm using your LM239A-EP part in a design. I'm using three out of the four comparators. How do I terminate the unused comparator? Regards, Paul M.

  • Resolved

  • over 4 years ago
  • Amplifiers
  • Amplifiers forum

Didn't find what you are looking for? Post a new question.