Search tips
Showing 198 results View by: Thread Post Sort by
    Answered

  • RE: LM2904: LM2904

    Resolved
    Hi Marian, as Ron answered, yes, the output should go high then, as explained in the datasheet. But keep in mind that the performance of LM2904 (refering to speed, etc.) will be degraded when leaving the common mode input voltage range. Kai

  • LM2904-Q1: TECHNICAL ISSUE

    Part Number: LM2904-Q1 hi team At present, customers want to use the operation discharge to do the current sampling of three-phase motor, but the customer supply voltage is mainly 5V, but the customer does not sample, the voltage will reach 24V,The common…
    • Answered

  • LM2904: LM2904AVQPWRRB supply voltage

    Resolved
    Part Number: LM2904 Hi team, could you help me with this problem. what is the rating supply voltage of LM2904AVQPWRRB. in customer use case, The max Vsup+ is 19V, the max Vsup- is -9V, is that OK?
    • Resolved

  • RE: LM2904: Why the negative feedback output pin of the op amp outputs an abnormal negative pulse voltage

    Hi Ron, Thank you for your reply, but I don't think the parameter you mentioned is the cause of the abnormality of LM2904.I replaced the LM2904B on our circuit and tested it under the same conditions, but the same abnormal phenomenon still occurred as…
    • Answered

  • LM2904BA: LM2904 and LM358 Suffixes

    Resolved
    Part Number: LM2904BA Other Parts Discussed in Thread: LM2904 , LM358 Hi, The LM2904 and LM358 are released in B and BA versions, respectively. As far as I can see from the datasheet, the only difference between these is the offset voltage. Are the B and…
    • Resolved

  • LM2904 output 0.6V

    TI Thinks Resolved
    Other Parts Discussed in Thread: LM2904 , LM431 hello? We use lm2904 to configure and use battery low voltage cutoff circuit. In some products, the lm2904 output voltage is 0.6V instead of 12V. The output of the lm2904 is a method of driving the relay…

  • LMV341 / LM2904

    TI Thinks Resolved
    Other Parts Discussed in Thread: LM2904 , LMV341 , TLV9001 , TINA-TI Dear Dharmesh Joshi , Ron Michallick , team, Background: We have a need to build a circuit to read Conductivity/EC measurements. We have referenced your earlier discussion on related subjects…

  • LM2904-N: LM2904MX/NOPB

    TI Thinks Resolved
    Part Number: LM2904-N Hi experts, LM2904MX/NOPB is mass production on customer side. Now they find that the mark in the device is different for different batch. Could you share the meaning for the mark? Thanks. older mark: Current Mark: Best Regar…

  • LM2904-Q1: please help design a band pass filter with LM2904-Q1

    TI Thinks Resolved
    Part Number: LM2904-Q1 Hi Expert, Our customer use LM2904-Q1 to design a band pass filter. The pass frequency range is 100Hz~2KHz. Could you please kindly support? Thanks. BR, Elec Cheng

  • LM2904: The output is high than normal setting

    Part Number: LM2904 Dear Expert Test conditions: input voltage 230V, output 12V with half load 2.915A, abnormal because the power supply current equalizing IBUS voltage is high, the specification is 2.9-3.3V, the actual test is bad 3.41-3.43V, The failure…

Didn't find what you are looking for? Post a new question.