• 

  Red Yen

  • over 2 years ago
  • Amplifiers
  • Amplifiers forum

  LM324A: LM324A Internal clamping diode voltage

  • Resolved

  Part Number: LM324A Hi Support team May I know the Vf of Internal clamping diode thank you
• 

  JC Y

  • 11 months ago
  • C2000™ microcontrollers
  • C2000™ microcontrollers forum

  RE: LAUNCHXL-F28379D: Superimposed Circuit with DAC Produces Clipped Output using SGEN Waveform Generator

  Devin, Once again thank you for your help. I was able to eliminate the clipping by configuring the LM324A in dual-supply configuration as shown below. The DAC output was not set to above 300mV. The datasheet states the DAC output is linear between...
• 

  Wei-Hao Chen (TW-FAE)

  • over 2 years ago
  • Amplifiers
  • Amplifiers forum

  LM324A: LM324A Internal clamping diode rating

  • Resolved

  Part Number: LM324A Hi Support Team, My customer wants to know what is the negative voltage
• 

  Ian Wang

  • over 1 year ago
  • Amplifiers
  • Amplifiers forum

  LMV641: LMV641 Damage.

  • Resolved

  LMV641 & LM324A , the spec for abs. min input pin voltage should no lower than -0.3V: LMV641, Is this due
• 

  GaryC

  • over 3 years ago
  • Amplifiers
  • Amplifiers forum

  LM324A: LM324ADR Rthjc

  TI Thinks Resolved

  Part Number: LM324A May I know what is the LM324ADR SOIC14 Rthjc? I can’t find it in the datasheet. Thanks. Gary
• 

  Ron Michallick

  • over 2 years ago
  • Amplifiers
  • Amplifiers forum

  RE: LM324A: or INA117P: Voltage drop reading at different sections of a cable

  Ben, Use a differential amplifier for each section. An isolated single supply will be fine. The application ground will some connection the the cable ground due to the voltage taps on the cable being an input to the difference amplifiers. Here is...
• 

  Curtis Torrey

  • over 2 years ago
  • Amplifiers
  • Amplifiers forum

  LM324A: LM324AN vs LM324N - ESD Question

  TI Thinks Resolved

  Part Number: LM324A I have an old PCB that I am updating so that it will pass the 15kV air discharge test. It is using the LM324N, and LM324AN interchangeably as voltage follower. After protecting the output lines with Zeners, everything was going great...
• 

  Tim Claycomb

  • over 1 year ago
  • Amplifiers
  • Amplifiers forum

  RE: LM324-N: Does LM324-N have new version?

  Hi Gary, I recommend taking a look at the LM324A for better offset specifications. If you do not need the high supply voltage range the LM324A offers, I recommend taking a look at the LMV324A or the LM324LV. Thank you, Tim Claycomb
• 

  Tim Claycomb

  • over 2 years ago
  • Amplifiers
  • Amplifiers forum

  RE: LM324: Can LM324 and lm324A replace each other

  Hi Selina, Yes. The main difference between the two devices is that the LM324A has lower offset voltage than the LM324. Thank you, Tim Claycomb
• 

  Umesh Patil10

  • over 4 years ago
  • Amplifiers
  • Amplifiers forum

  RE: Constant current source using op-amp

  What is the major difference between LM342A and LM324AD? I am unable to find out datasheet of LM324AD My circuit gives 8mA for 5Kohm when LM324AD is used. And it gives only 2mA for 5Kohm when I use LM324A

Didn't find what you are looking for? Post a new question.

• Ask a new question