• 

  鄭怡玟

  • over 1 year ago
  • Power management
  • Power management forum

  LM73606EVM-5V-400K: LM73606EVM-5V-400K: Evaluation Module CAD files

  TI Thinks Resolved

  Part Number: LM73606EVM-5V-400K Hello, I plan to use the LM73606 in my next design. Are the CAD files used for the evaluation module available? I think it was done in Altium. That would be very helpful. Regards, Grace
• 

  user6202416

  • over 1 year ago
  • Simulation, hardware & system design tools
  • Simulation, hardware & system design tools forum

  WEBENCH® Tools/LM73606EVM-5V-400K: LM73606

  • Resolved

  Part Number: LM73606EVM - 5V - 400K Tool/software: WEBENCH® Design Tools Hi, I have bought the LM73606
• 

  Tsukui Yusuke

  • over 2 years ago
  • Power management
  • Power management forum

  RE: LM73605: About short circuit protection

  Katelyn-san, Thank you for your response and support. I conducted a short circuit test with evm to check the behavior of the soft saturation current pattern. I will write test conditions. And Attach the test situation. □Vin=19.5V,Vout=5V,Fsw=500kHz, L...
• 

  Toshihiro Watanabe

  • over 1 year ago
  • Power management
  • Power management forum

  LM73606: input and output ripple voltage

  • Resolved

  Part Number: LM73606 Hello, My customer would like to know the ripple voltage of LM73606EVM
• 

  zhang ping

  • 21 days ago
  • Power management
  • Power management forum

  TPS63020: switching frequency

  TI Thinks Resolved

  Part Number: TPS63020 Tps63020 switching frequency is fixed 2.4m, my VIN range is 2.5-5, Vout = 3.3V, IOUT = 1a, the front with a DC / DC - switching frequency 1.2m output 5V, as the tps63020 input, found that tps63020 no output, the front DC / DC switch...
• 

  Matt Hein

  • 1 month ago
  • Motor drivers
  • Motor drivers forum

  RE: DRV8323R: How to read the datasheet parameter UGB of the internal OP-amps

  Hello Michael, The unity gain bandwidth (UGB) is defined as 1MHz for all four gain settings, and it is measured using a 60pF load on the output (i.e. SOA). It is a very pessimistic specification, when in reality the amplifier has higher performance...
• 

  harshal dave

  • 1 month ago
  • Power management
  • Power management forum

  RE: TPS62260: TPS62260 output getting short

  If anyone is facing an issue with this. The following are the reasons for IC getting damaged. 1.) As the feedback pin is high impedance. If the divider circuit used is of the value above 400K. There are chances that during production testing or...
• 

  Shota Mago

  • over 2 years ago
  • Power management
  • Power management forum

  LM73606: Switching Node Fluctuation (falling edge)

  • Resolved

  me ask you about LM73606EVM . Switching node of LM73606 was fluctuated when falling as shown in below
• 

  Matthew Murdock

  • 1 month ago
  • Power management
  • Power management forum

  RE: TPS62160-Q1: DESIGN REVIEW

  Melbin, My only questions/concerns with your schematics are regarding the components connected to the EN pin. The 100k resistor between EN and GND should not be required as there is an internal 400k pull down resistor present on this pin when the...
• 

  Hongyang Hui

  • 3 months ago
  • Power management
  • Power management forum

  WEBENCH® Tools/LMR33630: LMR33630 would fail under 36V input

  • Resolved

  )/(fsw*K*Ioutmax)]*Vout/Vin, where Vout is 5V , Vin is 36V, fsw is 400k , Ioutmax is 3A and K is 0.2

Didn't find what you are looking for? Post a new question.

• Ask a new question