• LMH13000: Duty cycle

  

  Nitzan Shadmi

  Part Number: LMH13000 Tool/software: Hi, I am looking for a current supplier with an output of at least 120 mA (an minimal current of around 1 mA), up to 15 V output and1 usec pulse width that is either programable (able to give a specific duty cycle…

  • 14 days ago
  • Amplifiers
  • Amplifiers forum

• LMH13000: Restock date?

  

  Jacob Campbell

  Part Number: LMH13000 Tool/software: We would like to develop some hardware with the LMH13000, but there is no stock on ti.com at the time of this post. I have requested to be updated when stock comes in, but for planning purposes, I was wondering if…

  • 17 days ago
  • Amplifiers
  • Amplifiers forum
Answered

• LMH13000: questions for this device

  

  R.Fukunaga

  Resolved

  Part Number: LMH13000 Tool/software: Hi all, My customer is considering this device. 1) When is the RTM for this device? 2026? 2) Is a sample available? 3) Can this device output a constant current of 5A? The datasheet (see below) says it can…

  • Resolved

  • 2 months ago
  • Amplifiers
  • Amplifiers forum

• LMH13000: Termination for LVDS inputs in CW mode

  

  Nanjunda M1

  TI Thinks Resolved

  Part Number: LMH13000 Tool/software: Hi, I'm using the LMH13000 current driver for my laser driver design for CW mode (non-pulsed). I will be using the device in low current mode for my application. 1. In this case, I won't be using the EP-EN…

  • 2 months ago
  • Amplifiers
  • Amplifiers forum

• OPA2675: OPA2675 Design Application

  

  ?? ?

  TI Thinks Resolved

  Part Number: OPA2675 Other Parts Discussed in Thread: LMH13000 Tool/software: Hi, I want to use high-speed LTTL to load LED for communication. Can I use OPA2675 as the driver? Or is there any better solution?

  • 1 month ago
  • Amplifiers
  • Amplifiers forum

• OPA211: OPA211

  

  Ivy Li

  Part Number: OPA211 Other Parts Discussed in Thread: LMH13000 Tool/software: Hi, I want to design a constant current source composed of an operational amplifier and a push-pull circuit (for example, as shown in the following figure). May I ask if there…

  • 1 month ago
  • Amplifiers
  • Amplifiers forum

• ONET1130EP: Laser CW mode of operation settings

  

  Nanjunda M1

  TI Thinks Resolved

  Part Number: ONET1130EP Other Parts Discussed in Thread: LMH13000 Tool/software: Hi, I'm looking for the Continuous wavelength (CW) mode laser driver. Does this part support CW mode (without any modulation)? Regards, Nanjunda M

  • 3 months ago
  • Interface
  • Interface forum

• LMH34400DRLEVM: photodiode for LiFi

  

  Andrew Buckin

  TI Thinks Resolved

  Part Number: LMH34400DRLEVM Other Parts Discussed in Thread: LMH34400 , LMH13000 , LMH13000RQEEVM , LMG1025-Q1EVM Tool/software: Please advise a photodiode for Lifi with LMH34400? thanks Andrew.

  • 2 months ago
  • Amplifiers
  • Amplifiers forum

• LM3429: Laser Diode Driver to 6W recommendation

  

  Andrew Buckin

  TI Thinks Resolved

  Part Number: LM3429 Other Parts Discussed in Thread: LMH13000 Tool/software: Hi, advise a modern driver for a 6W Laser. I want to do engraving at home. Forward voltage of the diode is 5V so that the current can be adjusted from 1A to 5A. I want to power…

  • 3 months ago
  • Power management
  • Power management forum

• OPA690: Driver for a laser diode on OPA690

  

  Emil Agayev

  Part Number: OPA690 Other Parts Discussed in Thread: OPA357 , , LMH13000 Tool/software: Hello team. I have built a driver for a laser diode on OPA690. The control signal is a sine wave 40 kHz, 1.8 V. The thing is that at the output there is only a…

  • 3 months ago
  • Amplifiers
  • Amplifiers forum

Didn't find what you are looking for? Post a new question.