Search tips
Showing 24 results View by: Thread Post Sort by
    Answered

  • LMH6601: What would happen if the SD_PIN (5PIN) was not at a constant level?

    Resolved
    Part Number: LMH6601 Tool/software: Dear Specialists, My customer has a question about SD pin. I would be grateful if you could advise. --- According to the LMH6601 datasheet, p. 20, 7.2.1 Shutdown Capability and Turn On/Off Behavior, ---This…
    • Resolved
    • Answered

  • LMH6601: LMH6601 .MOD File Unusable in PSPICE

    Resolved
    Part Number: LMH6601 Hi all, I tried using the PSPICE file for the LMH6601 but appears to be in a different file format that is unusable in TI-PSPICE. Are there any .DSN or .OPJ files available for this part, or a specific method used to convert the…
    • Resolved
    • Answered

  • LMH6601: Request for schematic review

    Resolved
    Part Number: LMH6601 Other Parts Discussed in Thread: LM7705 , THS4211 , OPA836 , OPA838 , OPA830 Hello, Could we have our schematic reviewed? The LMH6601 circuit is on Sheet 17. The requirements are Square wave with adjustable amplitude between…
    • Resolved
    • Answered

  • LMH6601: video amplifier that supports NTSC, PAL, Tri-level Sync (HD)

    Resolved
    Part Number: LMH6601 Other Parts Discussed in Thread: LMH6611 , OPA820 , OPA692 , OPA693 , LMH6704 Hi Team, My customer is looking for a video amplifier that supports the following signal. - NTSC - PAL - Tri-level Sync (HD) Does LMH6601 support above…
    • Resolved

  • OPA2354: Product recommendation

    Part Number: OPA2354 Other Parts Discussed in Thread: TLV3542 , LMH6601 Tool/software: hi team, my customer needs an amplifier with higher output current similar with OPA2354.Do u have some product to recommend？ thanks!

  • RE: OPA356-Q1: OPA236 alternative

    Hello Kevin, Our next smallest packages after the SOT-23 (DBV) are: SOT-SC70 (DCK) WSON (DSG) WQFN (RUN) X2QFN (DXB) I have filtered and sorted it to most to least suggested replacement: link to device suggestion comparison . If automotive…

  • OPA861：Designing and debugging a peak‐detect & hold circuit for 8 ns pulses using OPA861

    Part Number: OPA861 Other Parts Discussed in Thread: LMH6601 , OPA847 , OPA860 Tool/software: Hello TI experts, I am designing a photodiode-based peak-detect & hold circuit to capture ultra-narrow optical pulses (8 ns pulse width) at two repetition…
    • Answered

  • RE: THS5641A: Request for schematic review

    Resolved
    Hi Jim, I have updated to a single supply design. The edges of the square wave are not as sharp but acceptable. I also have an option to use 5.0V as opposed to 3.3V. Thanks for pointing out the V+ - V- being limited to 5.5 ~ 6V. I have moved them…
    • Answered

  • high speed amp

    Resolved
    Other Parts Discussed in Thread: LMH6601 , OPA836 Looking for similar device like LMH6601, but with lower Iq, of around </=2.5MA Its needed to replace ADI, ADA4851
    • Resolved
    • Answered

  • RE: Noise in transimpedance circuit using LMP7717

    Resolved
    Hello Phung, If you can work with +/-5V supplies OPA656 is a very good amplifier. Also, you can try the LMH6601 and see if it meets your needs http://www.ti.com/lit/ds/symlink/lmh6601.pdf Samir

Didn't find what you are looking for? Post a new question.