Because of the holidays, TI E2E™ design support forum responses will be delayed from Dec. 25 through Jan. 2. Thank you for your patience.



Search tips
Showing 17 results View by: Thread Post Sort by
    Answered

  • LMH6601: What would happen if the SD_PIN (5PIN) was not at a constant level?

    Resolved
    Part Number: LMH6601 Tool/software: Dear Specialists, My customer has a question about SD pin. I would be grateful if you could advise. --- According to the LMH6601 datasheet, p. 20, 7.2.1 Shutdown Capability and Turn On/Off Behavior, ---This pin must…
    • Resolved
    • Answered

  • LMH6601: Request for schematic review

    Resolved
    Part Number: LMH6601 Other Parts Discussed in Thread: LM7705 , THS4211 , OPA836 , OPA838 , OPA830 Hello, Could we have our schematic reviewed? The LMH6601 circuit is on Sheet 17. The requirements are Square wave with adjustable amplitude between 1.5V and…
    • Resolved
    • Answered

  • LMH6601: video amplifier that supports NTSC, PAL, Tri-level Sync (HD)

    Resolved
    Part Number: LMH6601 Other Parts Discussed in Thread: LMH6611 , OPA820 , OPA692 , OPA693 , LMH6704 Hi Team, My customer is looking for a video amplifier that supports the following signal. - NTSC - PAL - Tri-level Sync (HD) Does LMH6601 support above? Best Regards…
    • Resolved
    • Answered

  • LMH6601: LMH6601 .MOD File Unusable in PSPICE

    Resolved
    Part Number: LMH6601 Hi all, I tried using the PSPICE file for the LMH6601 but appears to be in a different file format that is unusable in TI-PSPICE. Are there any .DSN or .OPJ files available for this part, or a specific method used to convert the LMH6601…
    • Resolved

  • RE: OPA2354: Product recommendation

    Hi Zoey , We have LMH6601 with 150mA output current. The performance is similar to OPA2354 except for being NRI RRO and single channel device. Thanks Vikas J
    • Answered

  • RE: THS5641A: Request for schematic review

    Resolved
    Hi Jim, I have updated to a single supply design. The edges of the square wave are not as sharp but acceptable. I also have an option to use 5.0V as opposed to 3.3V. Thanks for pointing out the V+ - V- being limited to 5.5 ~ 6V. I have moved them to the…
    • Answered

  • RE: LMH6722: Video Distribution Amplifier

    Resolved
    Hello Gerald, Yes, high speed amplifier group is the correct place for this type of application. Michael already gave really good suggestions. I will add a couple more below and here is an app note for NTSC composite video applications . LMH6612 (closest…
    • Answered

  • OPA316: Pin Configuration and Functions (SC70/SOT23)

    Resolved
    Part Number: OPA316 Other Parts Discussed in Thread: OPA837 , LMH6601 , OPA838 , , TLV9062 , TLV9002 Dear Sirs, could you clarify the correctness of the different configurations for the SC-70 and SOT23 please. Datasheet SBOS703F –APRIL 2014–REVISED OCTOBER…
    • Resolved
    • Answered

  • high speed amp

    Resolved
    Other Parts Discussed in Thread: LMH6601 , OPA836 Looking for similar device like LMH6601, but with lower Iq, of around </=2.5MA Its needed to replace ADI, ADA4851
    • Resolved

  • Delay circuit using Ti IC LMH6628

    Other Parts Discussed in Thread: LMH6628 , LM7121 , LMH6601 Hi, I'm trying to use delay circuit as given in datasheet of LMH6628 (shown below) . I'm using a input pulse of 5V amplitude. R and C are 41.2 ohm and 33 pF respectively. + Vcc is 9V and -Vcc is…

Didn't find what you are looking for? Post a new question.