Because of the Thanksgiving holiday in the U.S., TI E2E™ design support forum responses may be delayed from November 25 through December 2. Thank you for your patience.



Search tips
Showing 21 results View by: Thread Post Sort by

  • LMH6609: Is there a Dual version similar to the LMH6609 for video applications ?

    Part Number: LMH6609 Other Parts Discussed in Thread: OPA2690 Hello Team, Does there happen to be a dual version of the LMH6609 that can be used for video applications as is described in the datasheet.

  • RE: LMH6609: Abnormal output waveform of LMH6609 with buffer configuration

    Hi Michael, I have test the OPA690 and found that this device will not cause oscillation in the same circuit of LMH6609. Could you share me your comments on this abnormal result? Thanks.
    • Answered

  • LMH6609: Abnormal output waveform of LMH6609 with buffer configuration

    Resolved
    Part Number: LMH6609 Other Parts Discussed in Thread: LMH6553 Hi Team, We penetrated LMH6609 at my customer side in a new project. But now we met an abnormal issue: 1. Below is the schematic used in customer side, just a buffer, Supply voltage is +/-5V…
    • Resolved

  • LMH6609: Butterworth filter application consult

    TI Thinks Resolved
    Part Number: LMH6609 Hi team, My customer is using this device to do Butterworth filter, could you please help review the schematic from customer's side? The signal frequency will be 0.3~30MHz. And they find that if they apply 1MHz signal, Vpp=0.948V…

  • LMH6609: @MHz parameter description

    Part Number: LMH6609 Hello Please describe the @.MHz parameter used in opamp selection table. Thanks.
    • Answered

  • Schematic and PCB of LMH6609 Evaluation Boards

    Resolved
    Other Parts Discussed in Thread: LMH6609 Hi, How to get the schematic and pcb layout files of LMH6609 reference design? Thank you, kerb
    • Resolved
    • Answered

  • RE: LMH6505: AGC circuits at V+/V- = 7V/0V

    Resolved
    Sima, After considering LMH6714 and LMH6609 power supply spec, my customer would like to use the following power supplies. LMH6605 V+ = LMH6714 V+ = LMH6609 V+ = 8V. LMH6605 V- = LMH6714V- = LMH6609 V- = GND. Is this acceptable? Best regards, K.Hirano

  • RE: LMH6624: LMH6624MAX NOPB amplifier noise reduction when used to measure the current with shunt.

    Hello Anurag, Is this with the LMH6609 or the LMH6624? The LMH6609 in this case is not decompensated, but is lower bandwidth compared to LMH6629. The above table looks to be the expected design requirements. Is the measured scope with input or both…

  • LMH6624: LMH6624: LMH6624MAX NOPB amplifier noise reduction when used to measure the current with shunt.

    Part Number: LMH6624 Other Parts Discussed in Thread: LMH6609 , , LMH6629 Hi Please see the layout TOP and BOTTOM attached. I tried your points, but not helped. Please suggest to ahead. Positive and negative supply derived from +5V and -5V LDO.

  • RE: THS4271: Distribution amplifier 10MHz with Dliyannis structure filter

    I might have been missing a connection in my sim? Kai's looks great, here is his file witht he LMH6609 dropped in. the higher curve to the right was the LMH6609 Adding the cap load does not look bad, but again the THS4271 model looks way simplif…

Didn't find what you are looking for? Post a new question.