Search tips
Showing 55 results View by: Thread Post Sort by
    Answered

  • LMH6624: LMH6624/26 Output impedance Value at 10 Mhz

    Resolved
    Part Number: LMH6624 Other Parts Discussed in Thread: OPA838 Tool/software: Hi Support; I tried to measure output impedance at 10Mhz of LMH6624 by connecting 1k load resistor and 1v Ac source to the output of op amp on Ti pspice. I measured and calculated…
    • Resolved

  • LMH6624: What is important parameter of OP needed to care during TIA design?

    Part Number: LMH6624 Hi, When designing TIA for MPD and RSSI signal for optical engine, what is important parameter of OP needed to care about? TIA is used to translate current signal to voltage signal. I read an applicaiton note, which mainly focus…
    • Answered

  • LMH6624: Designing a Transimpedance Amplifier with LMH6624 IC for High Gain and Bandwidth

    Resolved
    Part Number: LMH6624 Other Parts Discussed in Thread: OPA858 Tool/software: Hi, I need to develop a transimpedance amplifier using the LMH6624 IC. My requirements are: Amplifier gain: 100 MV/I (Mega volt/Amp) Bandwidth: 600 kHz Input photodiode current…
    • Resolved

  • LMH6624: NC pin

    TI Thinks Resolved
    Part Number: LMH6624 Tool/software: Hi All, I have a question about the NC terminal of the LMH6624. Is it okay to apply a voltage to the NC terminal? If it's not connected internally, I don't think there's a problem. The reason I want to apply…

  • LMH6624: LMH6624: LMH6624MAX NOPB amplifier noise reduction when used to measure the current with shunt.

    Part Number: LMH6624 Other Parts Discussed in Thread: LMH6609 , , LMH6629 Hi Please see the layout TOP and BOTTOM attached. I tried your points, but not helped. Please suggest to ahead. Positive and negative supply derived from +5V and -5V LDO.
    • Answered

  • LMH6624: Delete this Thread : LMH6624: We require Reference Design Schematic-Gerber and BOM.

    Resolved
    Part Number: LMH6624 Dear Sir/Madam, Kindly delete my entire email thread conversation and Design files related with below e2e TI thread at the earliest. I have tried to delete all communication at my end but looks like they are still appeared. Please…
    • Resolved

  • LMH6624: LMH6624MAX NOPB amplifier noise reduction when used to measure the current with shunt.

    TI Thinks Resolved
    Part Number: LMH6624 Other Parts Discussed in Thread: LMH6629 , LMH6609 , OPA855 I am using this IC for voltage amplification for measuring current with shunt value of 0.03E. What I am seeing here is, 800mV sine wave with time 5ns. [measurement scale…
    • Answered

  • LMH6624: LMH6624MA low capacitance input overvoltage protection

    Resolved
    Part Number: LMH6624 Other Parts Discussed in Thread: LM7171 , OPA690 , OPA820 , OPA656 Hi, I am using the LMH6624MA with an ADP, which is biased at 500V, can you please suggest a low capacitacnce protection method in case the 500V ends up on the input…
    • Resolved

  • LMH6624: PSpice for ADS

    Part Number: LMH6624 Hi, I would like to confirm the pin assignment for LMH6624 in Pspice model. The Pspice model pin assignment is given as * PINOUT ORDER +IN -IN V+ V- OUT * PINOUT ORDER 1 2 3 4 5 .SUBCKT LMH6624 1 2 3 4 5 While in Tina model…
    • Answered

  • LMH6624: Need Spice Model.

    Resolved
    Part Number: LMH6624 I'm looking for the Spice Model.
    • Resolved

Didn't find what you are looking for? Post a new question.