Answered

• LMK03328EVM: LMK03328 EVM EEPROM writing with TICSPRO-SW

  

  Hirotaka Matsumoto

  Resolved

  Part Number: LMK03328EVM Other Parts Discussed in Thread: TICSPRO-SW , LMK05318 , LMK05318B Hi all Would you mind if we ask LMK03328EVM? We tried to operete EEPROM writing with LMK03328EVM using TICSPRO-SW, however it couldn't. <TICSPRO-Sw version> <TICSPRO…

  • Resolved

  • over 3 years ago
  • Clock & timing
  • Clock & timing forum
Answered

• LMK03328EVM: how to evaluate LMK03328

  

  Toshiro Imi

  Resolved

  Part Number: LMK03328EVM Other Parts Discussed in Thread: LMK03328 , USB2ANY Hello, Our customer is planning to test LMK03328 by programming via I2C. While I have checked some documents, LMK03328EVM would be the best but I am not sure if he needs USB2ANY…

  • Resolved

  • over 4 years ago
  • Clock & timing
  • Clock & timing forum

• RE: LMK03328EVM: Can't communicate via I2C with the LMK03328EVM

  

  Timothy T

  Hello Snow, Glad you were able to accomplish what you needed. That is a good point. We should improve the user experience for when you directly type in the I2C address. Thanks for the feedback. Note with I2C mode, if you are writing to registers…

  • over 6 years ago
  • Clock & timing
  • Clock & timing forum

• RE: LMK03328EVM: PLL is not locking

  

  Hao Z

  Hello Kerry, Fractional order can help with spur optimization but it doesn't affect PLL lock status. I loaded the " PLL1 TICS Pro FREF 44MHz.tcs " that you attached previously and all outputs look good to me and both PLLs locked with no problem. If…

  • over 6 years ago
  • Clock & timing
  • Clock & timing forum

• LMK03328EVM: Jumper 3 on schematic

  

  ttd

  TI Thinks Resolved

  Part Number: LMK03328EVM Dear Technical Support Team, I have a question about schematic of LMK03328EVM. LABEL PINS of Jumper 3(J3) shows "1=3.3V". According to table 2 of datasheet ,this pin is for 5V. Is it typo? Best Regards, tt…

  • over 8 years ago
  • Clock & timing
  • Clock & timing forum

• LMK03328EVM: No output signals at the output ports

  

  Errol Leon6

  TI Thinks Resolved

  Part Number: LMK03328EVM Other Parts Discussed in Thread: CODELOADER , TICSPRO-SW Hello, My customer is testing the eval board now and having issues of getting no output out of the output ports. The figure below shows a high level of what the EVM is…

  • over 7 years ago
  • Clock & timing
  • Clock & timing forum

• LMK03328EVM: CodeLoader 4 Interface GUI issue

  

  Cassidy

  TI Thinks Resolved

  Part Number: LMK03328EVM Other Parts Discussed in Thread: CODELOADER Hi, I recall there being a solution guide on how to fix the GUI/Interface issue on CodeLoader 4 on the "Inputs/PLLs", "Outputs", "Status", and "EEPROM" pages. See the below screenshot…

  • over 8 years ago
  • Clock & timing
  • Clock & timing forum
Answered

• LMK03328EVM: about GPIO0 and PLL SYNCEN

  

  ACGUY

  Resolved

  Part Number: LMK03328EVM Hi, By setting SYNCN_SW OFF on the GUI and SYNCEN of PLL OFF, you can check the CLK output even if GPIO 0 on the evaluation board is OPEN. Is there any inconvenience if I use it under such conditions? Regards, ACGUY

  • Resolved

  • over 8 years ago
  • Clock & timing
  • Clock & timing forum
Answered

• LMK03328EVM: About output format setting on Code-Loader

  

  ACGUY

  Resolved

  Part Number: LMK03328EVM Other Parts Discussed in Thread: LMK03328 Hi, I setting work for registers of LMK03328. Please let me know that how to set output for LVDS format on Code-Loader. Regards, ACGUY set for LVDS format.pdf

  • Resolved

  • over 8 years ago
  • Clock & timing
  • Clock & timing forum
Answered

• Unable to program the EEPROM LMK03328EVM

  

  Kiran Sadasivan

  Resolved

  Other Parts Discussed in Thread: LMK03328EVM , LMK03328 New LMK03328EVM purchased, Connected with USB cable to the PC(USB identify working) HWCTRL = 0,RSEL = 1, GPIO0 = 1, GPIO1 = 0, GPIO2 = 1, GPIO3 = 1, GPIO4 = 1, GPIO5 = Mid Default EEPROM settings…

  • Resolved

  • over 9 years ago
  • Clock & timing
  • Clock & timing forum

Didn't find what you are looking for? Post a new question.