Answered

• LMK05318: Output configuration

  

  Vincent Chen64988

  Resolved

  Part Number: LMK05318 Hi Team, My customer would like to know how to configure CH6 as 1.8V CMOS single-end output? The VDDO is 3.3V in SCH. Thanks a lot. Vincent Chen

  • Resolved

  • 15 days ago
  • Clock & timing
  • Clock & timing forum

• LMK05318: Support 1588 V2

  

  Rocky Chen

  TI Thinks Resolved

  Part Number: LMK05318 Hi Expert Do we have Clock solution that can support 1588 V2? That being said to support SyncE (G.8262) and T-BC Class-D (G.8273.2). This is required in 5G Front-hual, I think we should have some experience on this. Could you share…

  • 1 month ago
  • Clock & timing
  • Clock & timing forum
Answered

• LMK05318: Kvco numeric of VCO1 and VCO2 for PLLatinum

  

  Hirotaka Matsumoto

  Resolved

  Part Number: LMK05318 Other Parts Discussed in Thread: LMK05028 , LMK03328 Hi all Would you mind if we ask LMK05318? How much is the Kvco numeric of VCO1 and VCO2? As the background of this question, we would lile to simulate using PLLatinum. On PLLatinum…

  • Resolved

  • 2 months ago
  • Clock & timing
  • Clock & timing forum
Answered

• LMK05318: LMK05318 input mode configuration

  

  Frank Xiao

  Resolved

  Part Number: LMK05318 Hi team, My customer is using the LMK05318 now with 50ohm pull down configuration. But the front edge is LVCOMS output, so the system voltage is too low with 50ohm SE configuration. 1. How to deal with the terminator resistors? 2. Whether…

  • Resolved

  • 6 months ago
  • Clock & timing
  • Clock & timing forum
Answered

• LMK05318EVM: How to set LMK05318 on the EVM to 300MHz and 400MHz with TICS Pro

  

  Aldo Oliveri

  Resolved

  Part Number: LMK05318EVM I am using the device for the first time and our application requires an output of 300MHz or 400MHz. Using the TICS Pro software i can re-program from the default 156.25MHz to 100MHz or 200MHz with the default settings in place…

  • Resolved

  • 24 days ago
  • Clock & timing
  • Clock & timing forum
Answered

• LMK05318: Setting up problems with configuration

  

  Roman Ehrle

  Resolved

  Part Number: LMK05318 Other Parts Discussed in Thread: USB2ANY Hello, I actually work with the network synchronizer LMK05318RGZT for generation of low-jitter reference clock of an FPGA-SERDES for optical communications. So far I tried putting a configuration…

  • Resolved

  • 2 months ago
  • Clock & timing
  • Clock & timing forum

• LMK05318: new clk requirement as LMK05318

  

  Frank Xiao

  TI Thinks Resolved

  Part Number: LMK05318 Hi team, My customer is using the LMK05318 now. We have new requirements below. Not sure whether we have have some recommended sockets based on the request. Thanks. 1) input 30.72M, output 1. 322.265625M 2. 10M or input 25M output 1.…

  • 7 months ago
  • Clock & timing
  • Clock & timing forum

• LMK05318: Unused output pins

  

  Miranda Gu

  TI Thinks Resolved

  Part Number: LMK05318 Hi team, My customers want to know how to configure the unused output pins. For unused differential outputs, customers should either float the pins if this channel disabled by registers, or terminate the pins if this channel active…

  • 4 months ago
  • Clock & timing
  • Clock & timing forum
Answered

• LMK05318: How to update both registers and EEPROM values?

  

  Miranda Gu

  Resolved

  Part Number: LMK05318 Hi team, My customer previously downloaded a wrong configuration (wrong clk output frequency) to LMK05318 EEPROM. Now t hey need to update the EEPROM (change the output frequency) through I2C , and also update the registers in the same…

  • Resolved

  • 4 months ago
  • Clock & timing
  • Clock & timing forum

• LMK05318: LMK05318 XO using clipped sine wave for input?

  

  Minki Li1

  TI Thinks Resolved

  Part Number: LMK05318 Can LMK05318 XO using clipped sinewave for input? About 0.8Vp-p How to connect to LMK05318? Thank You

  • 8 months ago
  • Clock & timing
  • Clock & timing forum

Didn't find what you are looking for? Post a new question.