Search tips
Showing 14 results View by: Thread Post Sort by
    Answered

  • LMK1C1103: IBIS Model

    Resolved
    Part Number: LMK1C1103 Other Parts Discussed in Thread: LMK1C1104 Tool/software: Hello, Is there an IBIS model for the LMK1C1103? If so, can you please share it? It does not have to be Power Aware Thanks, Victor
    • Resolved

  • LMK1C1103: Does the clock buffer's output follow the input in respect of rising and falling time?

    TI Thinks Resolved
    Part Number: LMK1C1103 Tool/software: Dear Friend I want to reduce rising and falling speed of the clock for EMI/EMC purpose by putting a ferrite bead in series with buffer's output. instead of adding ferrite bead for each clock, I am think just…
    • Answered

  • LMK1C1103: Output Impedance and Transmission Line Matching

    Resolved
    Part Number: LMK1C1103 Other Parts Discussed in Thread: LMK1C1102 , LMK1C1104 , Tool/software: The output impedance of the LMK1C1102 / LMK1C1103 / LMK1C1104 is shown in Section 7.5. This changes with voltage (Ro = 50Ω @ 3.3V, Ro = 52.5Ω @ 2.5V, Ro = 60 @ 1…
    • Resolved

  • LMK1C1103: Schematic review request

    TI Thinks Resolved
    Part Number: LMK1C1103 Hello there TI team, I am hoping you can provide a schematic review for a my design for a client. I am providing a 36.864MHz oscillating clock into the LMK and then outputting it to two microcontrollers and one ADC (a Texas Instruments…
    • Answered

  • LMK1C1103: IBIS PowerAwere

    Resolved
    Part Number: LMK1C1103 Hello, Is IBIS PowerAwere model avaialble for LMK1C1103PWR? Regards, Oba
    • Resolved
    • Answered

  • LMK1C1103: Pin compatibility LMK1C1104

    Resolved
    Part Number: LMK1C1103 Other Parts Discussed in Thread: LMK1C1102 , LMK1C1104 The product page mentions the LMK1C110x is pin compatible, but the datasheet shows NC for pin 7 of the LMK1C1103. Is it ok to connect pin 7 to pin 8 and 5?
    • Resolved

  • RE: DP83822IF: In rmii mode, RX is operational but TX is not operational on AM625 Custom Board

    Hi I am a hardware engineer working with the above questioner. The current circuit is applicable to both RGMII and RMII, and the input frequency is 25MHz, and is divided into three and transmitted from the LMK1C1103 IC. -. SOC -. ETH0 (DP83867 / in operation…

  • AM62A7: RMII reference clock connection with both RMII using when external clock source mode

    Part Number: AM62A7 Other Parts Discussed in Thread: LMK1C1103 , LMK1C1104 , Hi, TI engineers. I design RMII interface circuit. I will route the source from external 50MHz crystal oscillator to the MPU and 2 PHY chips. In TRM, I am confused about the description…

  • RE: AM6442: use of 2x RMII EPHY for CPSW

    Hi, is it possible to use the following clock buffer for the RMII-50MHz clock provided by the Sitara? https://www.ti.com/product/LMK1C1103 One output will be routed back to the Sitara RMII-REF pin used for both RMII-Interfaces of CPSW3G The remaining…
    • Answered

  • CDCM7005-SP: LVTTL or LVCMOS input/output

    Resolved
    Part Number: CDCM7005-SP Other Parts Discussed in Thread: LMK1C1103 , LMK04832-SP , Hi team Could you confirm whether the device can support LVTTL input/output or LVCMOS input/output as default condition? Regards, Noriyuki Takahashi
    • Resolved

Didn't find what you are looking for? Post a new question.