• LMK1D1208P: Thermal Management Information

  

  Nathaniel Fackrell

  Part Number: LMK1D1208P Need thermal management information for LMK1U1208MNZRSEP. Junction to case resistance top and bottom Junction to board resistance

  • 2 months ago
  • Clock & timing
  • Clock & timing forum
Answered

• LMK1D1208P: Input Voltage Specification

  

  Waldemar Henrich

  Resolved

  Part Number: LMK1D1208P Other Parts Discussed in Thread: CDCLVD1204 Hello Support team, I have a question regarding to the Specification of the LMK1D1208P Clock Buffer. In the Date Sheet on Page 6 the Input Voltage is specified as followed | VIN…

  • Resolved

  • 9 months ago
  • Clock & timing
  • Clock & timing forum

• LMK1D1208P: Update incorrect datasheet

  

  Todd Renner

  Part Number: LMK1D1208P Tool/software: As noted in previous posts, your datasheet pinout for IN0 is inverted. When will this be fixed in the datasheet?

  • over 1 year ago
  • Clock & timing
  • Clock & timing forum
Answered

• LMK1D1208P: Output signal is inverted

  

  Artem Porkhun

  Resolved

  Part Number: LMK1D1208P Other Parts Discussed in Thread: LMK1D1212 Hello! I am using LMK1D1208P. IN0 inputs connected to LVDS and have 100 Ohm termination. On output I get inverted input signal. I have IN_SEL pin tied to ground to select IN0_P and IN0_N…

  • Resolved

  • over 3 years ago
  • Clock & timing
  • Clock & timing forum
Answered

• LMK1D1208P: OE floating and clarification on banks

  

  Steve Widener

  Resolved

  Part Number: LMK1D1208P For the OEx pins. The datasheet states that the default is high – does this mean that for any inputs that I’ll always keep on, I can leave this pin floating? Or do I need to externally tie it high? Secondly, I noticed the datasheet…

  • Resolved

  • over 3 years ago
  • Clock & timing
  • Clock & timing forum

• LMK1D1208P: Problems with 1204 and 1208P clock chips

  

  ?? ?

  TI Thinks Resolved

  Part Number: LMK1D1208P Other Parts Discussed in Thread: LMK1D1204 Problem 1: LMK1D1208P is used as the clock buffer. Three 100Ms from the same chip are used as the system clock of three FPGAs. Two of them are OK. One of them has a problem with the clock…

  • over 3 years ago
  • Clock & timing
  • Clock & timing forum

• LMK1D2102L: LMK1D2102L: Inquiry regarding Output Enable/Disable Time and alternative recommendations

  

  woosung kim

  Part Number: LMK1D2102L Other Parts Discussed in Thread: LMK1D1208P Hello TI Support Team, I am currently considering the LMK1D2102L for my design, but I noticed that the Output Enable and Disable Time (t_en/disable) is not specified in its datasheet…

  • 3 months ago
  • Clock & timing
  • Clock & timing forum
Answered

• LMK1D1208EVM: Output Swing

  

  Gruffalo

  Resolved

  Part Number: LMK1D1208EVM Other Parts Discussed in Thread: LMK1D1208 , , LMKDB1108 , LMK1D1208P Dear Sir or Madam, in the datasheet of the LMK1D1208 I see the following entry: how can I achieve with the LMK1D1208 500mV output swing so 1 Vpp diff…

  • Resolved

  • 5 months ago
  • Clock & timing
  • Clock & timing forum

• TMUX1308A: Differential Signal MUXing

  

  Hideki Hayashi1

  TI Thinks Resolved

  Part Number: TMUX1308A Other Parts Discussed in Thread: LMK00306 , LMK1D1208P Tool/software: Hi team, Customer wants a MUX or distribution IC for LVDS (2.4MHz, 200ohm differential impedance). The configulation is 1 input and 6 output. Since input is…

  • over 1 year ago
  • Switches & multiplexers
  • Switches & multiplexers forum

• CDCLVC1108: logic level translation

  

  Matthew Plante

  TI Thinks Resolved

  Part Number: CDCLVC1108 Other Parts Discussed in Thread: LMK1C1108 , LMK00338 , LMK1D1208P Tool/software: I'm trying to verify if I power the CDCLVC11xx from 2.5V (so I can get 2.5V outputs), can I drive the input with a 3.3V signal? I assume no since…

  • over 2 years ago
  • Clock & timing
  • Clock & timing forum

Didn't find what you are looking for? Post a new question.