Search tips
Showing 43 results View by: Thread Post Sort by
    Answered

  • LMV393-Q1: Window comparator in datasheet.

    Resolved
    Part Number: LMV393-Q1 Hello, I am using the LMV393LV as a window comparator. I looked at the schematic you had on the datasheet and it appears to me that the in+ and in- are flipped on the amps. Would you please confirm that it's a typo. Below is…
    • Resolved
    • Answered

  • LMV393-Q1: Common-mode input voltage range at VCC=5V, full temperature range(-40C ~ 125C)

    Resolved
    Part Number: LMV393-Q1 Hello team, My customer considering using LMV393-Q1 in the automotive application. So this team would like to know about the VICR( Common-mode input voltage range) spec at VCC=5V and full temperature range(-40C ~ 125C). Because the…
    • Resolved

  • LMV393: When we used LMV393IDGKR, we found that the waveform output of the comparator was a little strange

    TI Thinks Resolved
    Part Number: LMV393 Other Parts Discussed in Thread: TLV7042 Hi TI expert, as shown below，What causes the red 2.8us noise in the following picture?
    • Answered

  • LMV393: Operation outside the Input Common-mode Voltage Range

    Resolved
    Part Number: LMV393 Dear Specialists, My customer is considering LMV393 and has a question. I would be grateful if you could advise. --- Could you please see attached file（competitor's application note). According to the application note, Even if…
    • Resolved
    • Answered

  • LMV393: Do you have any data of OUT rising/faiii of LVM393.

    Resolved
    Part Number: LMV393 Hello guys, One of my customers would like to get LMV393 output rising time/falling time(Tr/Tf?) data to use for their new products. Could you please tell me those data if you have? Your reply would be much appreciated. Best regards…
    • Resolved

  • Output voltage recomendation for LMV393

    TI Thinks Resolved
    Other Parts Discussed in Thread: LMV393 , TLV1702 , TLC352 , TLC372 , LM393 The output of the LMV393 is open collector, but the datasheet recommends that the output voltage be Vcc + 0.3V Max. I am looking to pull up the output to 12V. Can I do that?

  • LMV393: Switching Functionality VIN < 300mV

    Other Parts Discussed in Thread: LM393 Hi Jian I'm using the alternative part LM393 and I'm having a similar problem with the switching functionality. even when the VIN is less by 300mV than Vref the comparator is switching output state. Here…

  • LMV393: Output Current characteristics

    Part Number: LMV393 LMV393 Hi, The output current (sinking) characteristics, as mentioned in datasheet, is specified with a minimum value and a typical value (depending of the Supply voltage). i.e. @ 5Vcc Iol typ is 84 mA. Does this value is a limit (typical…

  • LM393: Problem with LM393D and LMV393

    Part Number: LM393 Other Parts Discussed in Thread: LMV393 Hi everybody, I was using a LM393D as window detector in one of my design. When the voltage is between 1 and 2.8V, my output is 3.3V and when the input voltage is outside of these values, I got…
    • Answered

  • LMV393 VCIM range vs output status

    Resolved
    Other Parts Discussed in Thread: LMV393 Hi, About VCIR of LMV393, please let questions. The LMV393 use with Vcc=+5V. From the data sheet(SLCS136T), VCIR (Common-mode input voltage range) is specified in the -0.1V to +4.2V. To us IN- (4pin) terminal, input…
    • Resolved

Didn't find what you are looking for? Post a new question.