• LMV772: 1.LMV772QMMX/NOPB 2.TLV3502AQDCNRQ1

  

  Shrinitha S

  TI Thinks Resolved

  Part Number: LMV772 Other Parts Discussed in Thread: TLV3501A-Q1 Tool/software: Please provide aFMEDA ,DFME and safety document for the below component 1.LMV772QMMX/NOPB 2.TLV3502AQDCNRQ1

  • 8 months ago
  • Amplifiers
  • Amplifiers forum

• LMV772-Q1: LMV772QMMX/NOPB

  

  LAKSHMISHREE B P

  Part Number: LMV772-Q1 Tool/software: Hi Please provide LMV772QMMX/NOPB (5 pins) Safety manual for this and also Pin FMEA/DFMEA. Thanks Regards, Lakshmishree B P

  • 7 months ago
  • Amplifiers
  • Amplifiers forum
Answered

• LMV772-Q1: Deciding on the input voltage range wrt to I/P common mode voltage

  

  Francis_93

  Resolved

  Part Number: LMV772-Q1 Other Parts Discussed in Thread: LMV772 Tool/software: I am using the opamp LMV772. I have non-Inverting negative feedback opamp configuration with gain is 11. The opamp I/P is connected to a voltage divider and the application…

  • Resolved

  • 9 months ago
  • Amplifiers
  • Amplifiers forum

• LMV772: Absolute max rating (V+)

  

  User

  TI Thinks Resolved

  Part Number: LMV772 Hello team, We are using LMV772QMMX in our application and the op-amp is supplied by a 5V regulator. During a failure condition for the regulator, we may observe an overshoot for a very small duration (~80ns) on the VDD5 line. …

  • over 2 years ago
  • Amplifiers
  • Amplifiers forum

• LMV772: LMV772 Top Mark decode

  

  Jack Lin4

  Part Number: LMV772 Dear TI team: Can you please help to explain the 4 digit on first line on TOP mark ? For example : 7932 or M8AB I have check all information on website and datasheet but no relative answer. looking forward to your early reply…

  • over 5 years ago
  • Amplifiers
  • Amplifiers forum

• LMV772: There are some error on datasheet(Rev.F) of lmv772

  

  John Henry

  TI Thinks Resolved

  Part Number: LMV772 Hi, I think there are some error on the datasheet lmv772. I download datasheet of lmv772 with a version "SNOSA04F –MAY 2004–REVISED SEPTEMBER 2010 " And I find maybe there are some errors: Page 16: Page 19:

  • over 5 years ago
  • Amplifiers
  • Amplifiers forum

• LMV772-Q1: error calculation?

  

  Chen Melina

  TI Thinks Resolved

  Part Number: LMV772-Q1 Other Parts Discussed in Thread: LMV772 Hi I used a TI op amp lmv772 in the application. Now I want to calculate the error caused by the op amp. Could you please help to check out the input offset and what other parameters can…

  • over 6 years ago
  • Amplifiers
  • Amplifiers forum
Answered

• LMV772-Q1: Disabling one of the channels in dual channel device

  

  Nikhil Jotwani

  Resolved

  Part Number: LMV772-Q1 Other Parts Discussed in Thread: LMV772 Hello, I am using a dual channel LMV772. Presently I need only one channel for my application. What is the method to diable the other Op-Amp in the device? Is it better to ground it or leave…

  • Resolved

  • over 8 years ago
  • Amplifiers
  • Amplifiers forum

• LMV772-Q1 Temperature Drift

  

  Takao Yamamoto

  Other Parts Discussed in Thread: LMV772-Q1 Dear all, I would like to know about temperature drift. LMV772-Q1 has two OpAmps in one IC. Do these two OpAmps have same temperature drift? Do these two OpAmps have same error of temperature drift…

  • over 10 years ago
  • Amplifiers
  • Amplifiers forum
Answered

• RE: Please provide HSPICE model for part number LMV772 Dual Precision, 17 MHz, Low Noise, CMOS Input Amplifier

  

  Britt Brooks - Online Design Tools

  Resolved

  Pravnav, There is a PSpice model (unencrypted) in the product folder. Britt

  • over 11 years ago
  • Simulation, hardware & system design tools
  • Simulation, hardware & system design tools forum

Didn't find what you are looking for? Post a new question.