TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 144 results View by: Thread Post Sort by
  • LMX2541: There is a significant difference between the simulated phase noise and the specification sheet

    user5883945
    user5883945
    TI Thinks Resolved
    Part Number: LMX2541 Dears, Why is there a significant difference between the phase noise simulated by the customer and the datasheet? The simulation data is much higher than the datasheet. The parameter configuration is the same as the datasheet. Can…
    • 16 days ago
    • RF & microwave
    • RF & microwave forum
  • Answered
  • LMX2541: Spurious emmission at VCO frequency + 430 MHz (measured with SQ2380E VCO variant)

    Reinier Seuren
    Reinier Seuren
    Resolved
    Part Number: LMX2541 Tool/software: Hi, I am using the LMX2541SQ2380E in full chip mode to generate a 2400-2450 MHz RF signal. I noticed in the spectrum measurement of there is a large spurious peak at the VCO frequency + 430 MHz (for all measured VCO…
    • Resolved
    • over 1 year ago
    • Clock & timing
    • Clock & timing forum
  • LMX2541: youtube training/demonstration videos

    Mathew Bell
    Mathew Bell
    TI Thinks Resolved
    Part Number: LMX2541 I found several videos demostrating the performance of the LMX2541 on TI's youtube channel. There is a 5 part series. I have only been able to find parts 1, 4 and 5. I would very much like the chance to watch parts 2 and 3. Also,…
    • over 1 year ago
    • Clock & timing
    • Clock & timing forum
  • Answered
  • LMX2541: External clock

    Danilo A.
    Danilo A.
    Resolved
    Part Number: LMX2541 Hi Team, Using an external clock oscillator, such as SRS PRS10 Rubidium clock, with the LMX2541 board rather than the internal crystal oscillator, I understand that a resistor must be swapped from the internal oscillator to the…
    • Resolved
    • over 2 years ago
    • Clock & timing
    • Clock & timing forum
  • LMX2541: the alternative recommendation

    Zoey Wu
    Zoey Wu
    TI Thinks Resolved
    Part Number: LMX2541 Other Parts Discussed in Thread: LMX2571 Hi team, could u kindly help to recommend our solution to replace LT5560 and ADF4360-8BCPZRL7? Thanks!
    • over 2 years ago
    • Clock & timing
    • Clock & timing forum
  • LMX2541: rising edge/falling edge of the 1GHz sine clock signal output by the FPGA configuration was not ideal

    Jayden Qiu
    Jayden Qiu
    TI Thinks Resolved
    Part Number: LMX2541 Hi Team, This is FAE Jayden, my customer uses LMX2541SQE3030E/NOPB in their system. The customer found that the rising edge/falling edge of the 1GHz sine clock signal output by the FPGA configuration was not ideal (see the test…
    • over 2 years ago
    • Clock & timing
    • Clock & timing forum
  • LMX2541: Default register settings at power up unclear

    Markus Roggli
    Markus Roggli
    TI Thinks Resolved
    Part Number: LMX2541 We are using the LMX2541SQ3740E and discovered the following strange behavior: At power up the state of the pin 20 (Ftest/LD) is not well defined. We have installed a 1k Ohm pull-up to 3.3V on this pin. If not configured some devices…
    • over 3 years ago
    • Clock & timing
    • Clock & timing forum
  • LMX2541: Using Two PLL on the Same Micowire Bus

    TI-CSC
    TI-CSC
    TI Thinks Resolved
    Part Number: LMX2541 Other Parts Discussed in Thread: LMX2592 Hello E2E Experts, Good day. We use two PLL LMX2541SQ3740E on the same Microwire bus and use the chip in "Full Chip Mode". Programming is done only once. On page 37, the following information…
    • over 2 years ago
    • Clock & timing
    • Clock & timing forum
  • LMX2541: Regarding the RMS jitter related information

    Maitry Khambhati
    Maitry Khambhati
    TI Thinks Resolved
    Part Number: LMX2541 Hello support team, What would be the RMS jitter for LMX2541 in the integrated BW of up to 20 MHz? I am looking for the RF source which can generate 110 MHz sine wave frequency and have the ultra low RMS jitter in femto second.…
    • over 3 years ago
    • Clock & timing
    • Clock & timing forum
  • Answered
  • LMX2541: Initial value of REOUT[1:0] in register R6 after power-on

    kouichirou shimoyama
    kouichirou shimoyama
    Resolved
    Part Number: LMX2541 What is the initial value of REOUT[1:0] in register R6 after power-on?
    • Resolved
    • over 3 years ago
    • Clock & timing
    • Clock & timing forum
>

Didn't find what you are looking for? Post a new question.

  • Ask a new question