Answered

• LMX2694-EP: LMX2694-EP Poor Locking Performance

  

  Samuel Compton

  Resolved

  Part Number: LMX2694-EP Hi, We are using LMX2694 to create a 9280 MHz clock from a 300 MHz osc in. We notice that the LMX2694 reports it's "locked" per R110 (readback = 0x0448). However, we notice on triggering the calibration that its output starts…

  • Resolved

  • 3 days ago
  • Clock & timing
  • Clock & timing forum
Answered

• LMX2694-EP: TICS Pro configuration of LMX2694

  

  Adi R

  Resolved

  Part Number: LMX2694-EP Hi, I am working with TICS pro to configure LMX2694 synthisizers. I had the synths working as expected but after some write registers operations I have lost the output signal from the synths. I am relative basic user and using…

  • Resolved

  • 3 months ago
  • Clock & timing
  • Clock & timing forum

• PLLATINUMSIM-SW: LMX2694-EP Device is not available in the tool

  

  Maharajan P

  TI Thinks Resolved

  Part Number: PLLATINUMSIM-SW Other Parts Discussed in Thread: LMX2694-EP , LMX2694-SEP Dear team, I am using LMX2694-EP part in my design. I have installed "Setup_PLLatinumSim-1.6.9.1 " tool in my PC, LMX2694 or LMX2694-EP device is not available in…

  • 17 days ago
  • Clock & timing
  • Clock & timing forum

• LMX2694-EP: LMX2694SRTCTEP PLL not locking issue

  

  Maharajan P

  Part Number: LMX2694-EP Dear Team, I am using LMX2694SRTCTEP, When reading Register R110, i obtain a value of 0x0759 (binary: 0111 0101 1001). According to the LMX2694 datasheet, bits [10:9] indicate the VCO status, and the reported value corresponds…

  • 19 days ago
  • Clock & timing
  • Clock & timing forum
Answered

• LMX2694-EP: Pout with temperature

  

  David Park

  Resolved

  Part Number: LMX2694-EP Hi, Could you share the Pout performance of LMX2694-EP/-SEP under -25~60C? Thanks.

  • Resolved

  • 7 months ago
  • Clock & timing
  • Clock & timing forum
Answered

• LMX2694-EP: LVDS OSCIN

  

  Samuel Compton

  Resolved

  Part Number: LMX2694-EP Other Parts Discussed in Thread: LMK1D2102 Hi, I notice that VOSC input range for LMX2694 is 0.4V - 2V for input frequencies greater than 20 MHz. The datasheet also recommends LVDS as differentialy input protocol. However…

  • Resolved

  • 5 months ago
  • Clock & timing
  • Clock & timing forum
Answered

• LMX2694-EP: Differential Mode Testing

  

  Jonathan Wamala

  Resolved

  Part Number: LMX2694-EP Hi, am i want to verify LMX2694-EP differential mode output for OUTA_PD on the evaluation card but am having trouble setting it up in continous mode where i can see proper 180 deg phase offset. Can you offer some insight? am using…

  • Resolved

  • 9 months ago
  • Clock & timing
  • Clock & timing forum
Answered

• LMX2694-EP: Cold sparing OSCIN_P / N inputs

  

  Robert Johnson

  Resolved

  Part Number: LMX2694-EP OSCIN_P / N inputs support cold sparing? Under what conditions can an ac coupled input signal be applied before power and not damage this part?

  • Resolved

  • 7 months ago
  • Clock & timing
  • Clock & timing forum

• RE: LMX2694-EP: Filter Design, Phase Noise, and Bode Plot for 10MHz Design

  

  Joseph Blank

  Hi Noel, Thank you very much for such a detailed response. To provide some additional context, I am using a 10 MHz square wave LVCMOS clock as input. I believe the best course of action would be to upconvert my 10 MHz square wave LVCMOS clock input…

  • 8 months ago
  • Clock & timing
  • Clock & timing forum
Answered

• LMX2694-EP: About the size of LMX2694SRTCTEP

  

  Yasunobu Ihara

  Resolved

  Part Number: LMX2694-EP Tool/software: LMX2694-EP.pdf Could you please provide the following information about the LMX2694SRTCTEP? ・The maximum and minimum values of the side electrode height of 0.2. ・The maximum, nominal, and minimum values of the…

  • Resolved

  • over 1 year ago
  • Clock & timing
  • Clock & timing forum

Didn't find what you are looking for? Post a new question.