• 

  Bobby Ludlum

  • over 6 years ago
  • MSP low-power microcontrollers
  • MSP low-power microcontroller forum

  RE: Non-Implemented modules

  Thanks Jens-Michael for the informative reply. That behavior is about what I assumed the MSP430 would do. However I do have a puzzling situation that I would like your opinion on. I am running an MSP430F1481 Rev S in a TI ZIF Socket connected to a TI...
• 

  Yoyo

  • over 10 years ago
  • MSP low-power microcontrollers
  • MSP low-power microcontroller forum

  The difference between the S version and AA version of MSP430F1481

  Our customer produce switch. He replaced the S version with AA version. The S worked very well before. There are some problems with AA. It failed to pass the test and can't download the program. So I wonder what difference between them that may cause...
• 

  James Evans

  • over 3 years ago
  • MSP low-power microcontrollers
  • MSP low-power microcontroller forum

  RE: MSP430F6726: Implementation of a Single-Phase Watt-Hour Meter

  Hello Pavel, EDIT: I didn't read past your first error. You already did this, and I didn't notice. Pavel Hristov We tried adding the following lines in io.h #elif defined(__ MSP430F6726 __) #define __MSP430_6726__ For your first error...
• 

  Fabion et Fronk

  • over 10 years ago
  • MSP low-power microcontrollers
  • MSP low-power microcontroller forum

  UART interrupt disable

  • Resolved

  Hello, we have a question concerning the USART interrupt handling using the MSP430F1481 device
• 

  Rishi Singhal

  • over 10 years ago
  • MSP low-power microcontrollers
  • MSP low-power microcontroller forum

  How I generate CLOCK in SPI AT45DB3210D

  • Resolved

  hello, My job to communicate between MSP430F1481 & AT45DB3210D. spi_init() { P5DIR |=0x0C
• 

  Kshatriya

  • over 10 years ago
  • MSP low-power microcontrollers
  • MSP low-power microcontroller forum

  Re: Which energy meter method more reasonable?

  Hi jens-Michael Gross, we have started a project "Three phase Energy metering" using ADE7758 with msp430f1481 and we are facing too many problems in calibration,i.e. as per our design it should calculate the Energies up to 60A ,but while...
• 

  Fabion et Fronk

  • over 11 years ago
  • Processors
  • Processors forum

  Use multiplexed GP0[15:8] after HPI boot process

  Hello, we do have a question regarding the multiplexed GP0/HPI pins of the TMS320C6418 DSP. We are developing an universal DSP Board with this DSP and a MSP430F1481 microcontroller serving as host for this system. This µC should initialize the...
• 

  krzysztof duma

  • over 5 years ago
  • Code Composer Studio™
  • Code Composer Studio™ forum

  RE: ccs_setup_ 5.5.0.00077 Offline installer error

  I have same problem. My log file: Log started 10/22/2015 at 12:30:49 Preferred installation mode : unattended Trying to init installer in mode unattended Mode unattended successfully initialized [12:30:49] eclipsedir = D:/ti/ccsv5_msp430/ccsv5/eclipse...
• 

  Fabion et Fronk

  • over 10 years ago
  • Processors
  • Processors forum

  Problem with HPI16 boot process

  Hello, we do have a problem with setting up our TMS320C6418 device using the HPI 16 boot process. I'm trying to make it short so if you need additional information on how we setup up things, don't hesitate to ask. The DSP HPI pins...
• 

  Kshatriya

  • over 10 years ago
  • MSP low-power microcontrollers
  • MSP low-power microcontroller forum

  Clarification on SPI initialiZation

  Hi, Is there any changes required in my SPI code , it is in four pin mode with external GPIO pin as chip select(so 3-pin) i am using msp430f1481, problem is that with bitbanking method i was able to transmit data and receive with an external flash...

Didn't find what you are looking for? Post a new question.

• Ask a new question