Search tips
Showing 7,245 results View by: Thread Post Sort by
    Answered

  • MSPM0G3507: Cannot enable plotting on MSPM0 analog configurator tool for my MSPM03507 LaunchPad

    Resolved
    Part Number: MSPM0G3507 to test M0 launchPad with Analog Configurator (I do click “Reconfigure Connected Deivce” to set configuration to my M0 LaunchPad) as the following screenshot. But I don’t see anything when I enable plotting on ADC0…
    • Resolved

  • DRV8305-Q1: SPI configuration example codes with MSPM0

    TI Thinks Resolved
    Part Number: DRV8305-Q1 Other Parts Discussed in Thread: DRV8305 Customer was designing DRV8305-Q1 for the sensorless BLDC with FOC control, together with MSPM0G MCU. They did not have experience on DRV and M0. Could you please help provide the example…

  • RE: LP-MSPM0L1306: Analog Configurator doesn't work

    Hi Gary, maybe I misunderstand your reply, but I am not talking about an out_of_box example from our SDK. What I was trying to say was, that if I try to import and rebuild an example from analog configurator in either CCS or Theia I am getting above mentioned…

  • LP-MSPM0G3507: Unable to Plot ADC with Analog Configurator & Unable to run program with CCS

    Part Number: LP-MSPM0G3507 Other Parts Discussed in Thread: MSPM0G3507 , LP-MSPM0L1306 , SYSCONFIG Hello everyone, I took a new LP, used it as delivered, and tried to do the ADC Plotting in the Analog Configurator I did the following: Set COM Port to Application…
    • Answered

  • MSPM0 - Can not configure any timer register (ex. TIMG0)

    Resolved
    Part Number: MSPM0 Hello, I've a problem regarding setting TIMG0 registers in MSPM0 controller. If I try to set any register to any value, nothing works. Is the TIMG0 register protected or something like that? I figured out, that also other timer…
    • Resolved

  • DAC088S085: Configuring for 8 simulatenous PWM inputs and analog outputs

    TI Thinks Resolved
    Part Number: DAC088S085 Hello, I am trying to use the DAC088S085 to output 8 analog voltages (0-5V) simulatenously - these will be used to apply a forward voltage to solar cells, so that they are all being driven at the same time. However, I am confused…

  • RE: DP83TG720S-Q1: How to configure Analog Loopback With Inbuilt Data-Gen？

    Hello, To ensure same setup, are you writing anything else into PHY prior to analog loopback commands? You can see in my code, I reset the PHY to default settings via Reg 0x1F = 0x8000. Can you please try this at the beginning of your write sequence? …

  • TMS320F280037C: Possible configuration for 3.3V analog & digital power supply

    TI Thinks Resolved
    Part Number: TMS320F280037C Other Parts Discussed in Thread: TIDA-01281 , SN6505B , Hi Team, I’m wondering – what is the most common way to supply analog 3.3V and digital 3.3V? I see https://www.ti.com/tool/TIDA-00951 and Common Documentati…

  • TLV320AIC3254EVM-K: Analog Input Configuration

    Part Number: TLV320AIC3254EVM-K Hi There are three analog input configuration examples on the AIC3254 CS Tool. The first one "High Performance Stereo Recording", the second one is "Low Power Stereo Recording" and the third one is "On-Board Differential…

  • RE: TMS320F2800137: By default, these pins function as analog pins and the GPIOs are in a high-impedance state. So AIO default as analog pins, but actually we must configure the register GPHAMSEL.

    Hi Shaoxing, Thanks for your follow-up. Can you do the following with the customer, and the project they are using? 1. Please use one of the ADC examples in C2000Ware unmodified on their board. See if the same 0.2/0.3V issue exists (it should not, even…

Didn't find what you are looking for? Post a new question.