Search tips
Showing 11 results View by: Thread Post Sort by
    Answered

  • MSPM0L1116: MSPM0L1116: Does IWDT Run in STANDBY1 When Using LFCLK?

    Resolved
    Part Number: MSPM0L1116 Hi expert, I would like to ask about the behavior of the IWDT on MSPM0L1116. If the IWDT is configured to use LFCLK as its clock source and is enabled before entering STANDBY1: • Does the IWDT actually continue…
    • Resolved

  • MSPM0L1116: Which situation osc accuracy is guranteed

    Part Number: MSPM0L1116 Hi, Let me confirm about below. * According to errata document, there is following description. This shows user should avoid to set multiplies of 4MHz. However, MSPM0L1116 do not have PLL and just have divider. So I wonder how…
    • Answered

  • MSPM0L1116: Is flash memory address continuous or not?

    Resolved
    Part Number: MSPM0L1116 From datasheet, MSPM0L1116 have 64kB flash size, and it is seprated to 2 flash banks. Bank 0: 0x0.0000 - 0x0.7FFF Bank 1: 0x1.0000 - 0x1.7FFF So the address assignment of this 64kB flash discontinuous? But from J-link…
    • Resolved

  • MSPM0L1116: Clarification on timer additional current compared to RA0E2 values

    TI Thinks Resolved
    Part Number: MSPM0L1116 Hi, In this thread I understand that MSPM0L1116 does not provide per-peripheral current specs, and it was suggested that enabling a timer in STANDBY mode does not significantly increase current: https://e2e.ti.com/support/microcontrollers…
    • Answered

  • MSPM0L1116: I2C.CFIFOSR.TXFIFOCNT is reset as 4 not 8

    Resolved
    Part Number: MSPM0L1116 From TRM, the reset value of this register should be 8. After I reset I2C peripheral, I read this register value is 4, not 8. The code I reset the I2C peripheral: /*! Enable I2C power*/ #define I2C_EnablePower(I2Cx) SET_BIT…
    • Resolved

  • MSPM0L1116: DMX To SPI Solution

    TI Thinks Resolved
    Part Number: MSPM0L1116 Other Parts Discussed in Thread: MSPM0G3507 hi Sir We are LED driver manufacturer, next generation product need to support The DMX togolopy We need a solution to be a bridge for DMX to SPI May I know if TI M0 have the…
    • Answered

  • MSPM0L1116: Why only mode-based current specs? Any per-peripheral current data?

    Resolved
    Part Number: MSPM0L1116 Hi, In the MSPM0L1116 (MSPM0L111x) datasheet, supply current is specified mainly by power modes (RUN/SLEEP/STOP/STANDBY). We could not find current consumption specs for individual digital peripherals (Timer/UART/I2C). We are…
    • Resolved

  • MSPM0L1116: RTC Interval Limitations and PWM operation in STANDBY1 Mode

    Part Number: MSPM0L1116 Other Parts Discussed in Thread: SYSCONFIG Hi All, Is there any way to count 10 seconds or 15 seconds using the RTC? I have confirmed that a 60‑second interval can be counted successfully. If the RTC cannot support such intervals…
    • Answered

  • LP-MSPM0L1117: Is the J-Link compatible with the MSPM0L1116?

    Resolved
    Part Number: LP-MSPM0L1117 Other Parts Discussed in Thread: MSPM0L1116 Hi All, Is the J-Link compatible with the MSPM0L1116? I have attached the results obtained from searching within the J-Link software, so please check them. Best Regards, I…
    • Resolved
    • Answered

  • MSPM0L1117: Is there a DATA Region in the MSPM0L1116.

    Resolved
    Part Number: MSPM0L1117 Other Parts Discussed in Thread: MSPM0L1116 Tool/software: Hi All, Does the MSPM0L1116 have a data storage area in Flash? My customer want to save input data when using the application. The data sheet does not show a DATA…
    • Resolved

Didn't find what you are looking for? Post a new question.