TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 41 results View by: Thread Post Sort by
    Answered
  • OPA1641: OPA1641 single supply through OPA27. OPA27 feeding two loads with 1/2 Vref

    Matteo Bonino
    Matteo Bonino
    Resolved
    Part Number: OPA1641 Other Parts Discussed in Thread: OPA27 Tool/software: Dear all, I'm currently designing an op amp buffer, based on the OPA1641 (part of a more general Hi-Fi preamplifier project). This buffer will receive audio signal from the output…
    • Resolved
    • 4 months ago
    • Audio
    • Audio forum
  • Answered
  • OPA1641: OPA1641 SPICE model question

    Andrew Coad
    Andrew Coad
    Resolved
    Part Number: OPA1641 Other Parts Discussed in Thread: TL081 , TL072 , TL082 , Hello, I'm modeling the input impedance of a simple non-inverting stage and finding that the impedance is very different from other TI JFET input opamps. Here is the simulation…
    • Resolved
    • over 4 years ago
    • Audio
    • Audio forum
  • Answered
  • OPA1641: Issues simulating opa1641 with single supply using tina ti

    Alassane GORY
    Alassane GORY
    Resolved
    Part Number: OPA1641 Hello, i'm having issues simulating a single supply opa1641 as a buffer. On the input, i have a sinewave, 100mv Vpp and a 100ohm internal resistance but the output is centered around 199mV. The singla amplitude is not the same…
    • Resolved
    • over 4 years ago
    • Audio
    • Audio forum
  • Answered
  • OPA1641: Input Voltage Noise Density vs Frequency lower when operating at 5V supply in Spice

    Ed Wilinski
    Ed Wilinski
    Resolved
    Part Number: OPA1641 Other Parts Discussed in Thread: TINA-TI Hi, I'm performing a Spice Noise model verification of the OPA1641 in both Tina and LTSpice. I have the OPA1641 in a voltage follower configuration and checked the model at both +/-15 Vsupply…
    • Resolved
    • over 3 years ago
    • Audio
    • Audio forum
  • Answered
  • OPA1641-Q1: On the input voltage buffer of microphone audio acquisition

    SHENG YANG
    SHENG YANG
    Resolved
    Part Number: OPA1641-Q1 Other Parts Discussed in Thread: INA1650 , JFE150 , INA1620 ALL HI! As shown in the figure below. The left J1 is the position of the external microphone. If I can't determine the mic_ The size of bias and the input voltage range…
    • Resolved
    • over 3 years ago
    • Audio
    • Audio forum
  • OPA1641: OPA1641 Application

    Hardy Ma
    Hardy Ma
    TI Thinks Resolved
    Part Number: OPA1641 Other Parts Discussed in Thread: OPA1642 , TL971 , RC4558 , OPA1662 , OPA1692 Hi TI, My application is: The external device only provides 8V power to the DSP module, and then the DSP module should output an audio signal with a…
    • over 7 years ago
    • Audio
    • Audio forum
  • Answered
  • OPA1641: Recommended TI part for +/-15V power supply

    Francisco Salomon1
    Francisco Salomon1
    Resolved
    Part Number: OPA1641 Other Parts Discussed in Thread: TPS65130 , TPS7A39 Hi, I'm developing a circuit for guitar including an OPA1641 as pre-amp, and 2 buffer stages. My design will use +/-15V, generated from +9V. In terms of power for those stages, the…
    • Resolved
    • over 5 years ago
    • Audio
    • Audio forum
  • Answered
  • TINA/Spice/OPA1641: Reporting Spice model error

    Brian Antheunisse
    Brian Antheunisse
    Resolved
    Part Number: OPA1641 Other Parts Discussed in Thread: TINA-TI , , OPA1671 Tool/software: TINA-TI or Spice Models Hi guys, My customer found this and wanted to report it to be fixed (not time sensitive, as it is not impeding their progress): "The…
    • Resolved
    • over 6 years ago
    • Amplifiers
    • Amplifiers forum
  • Datasheet error OPA1641/1642/1644

    Daniel Menes
    Daniel Menes
    Other Parts Discussed in Thread: OPA1641 Not sure if the forum is the right place to call this to TI's attention, but the datasheet for the OPA1641 audio op amp (and it's siblings) contains obvious errors in the electrical characteristics table. For example…
    • over 9 years ago
    • Amplifiers
    • Amplifiers forum
  • OPA1641 & THS4601 GBW for SVF

    Temmy Soesanto
    Temmy Soesanto
    Other Parts Discussed in Thread: OPA1641 , OPA827 , LME49860 , THS4601 Hi, I have seen in one post about minimum GBW for a filter, right now I have an audio filter project base on state variable filter using LME49860 & OPA1641 or OPA827 with: F: 665Hz…
    • SVF Filter.TSC
    • over 11 years ago
    • Amplifiers
    • Amplifiers forum
>

Didn't find what you are looking for? Post a new question.

  • Ask a new question