Because of the Thanksgiving holiday in the U.S., TI E2E™ design support forum responses may be delayed from November 25 through December 2. Thank you for your patience.



Search tips
Showing 50 results View by: Thread Post Sort by
    Answered

  • OPA1688: Simulation model clipping

    Resolved
    Part Number: OPA1688 Tool/software: I am using the simulation model for OPA1688ID rev E, when I put it in voltage follower configuration I get clipping at 3V with a 5V supply, is this supposed to happen?
    • Resolved

  • OPA1688: Single and Differential OPAMPs for MEMS MIC output

    TI Thinks Resolved
    Part Number: OPA1688 Other Parts Discussed in Thread: OPA1678 , OPA1637 , , OPA344 Tool/software: Hi Team, Customer is trying to design the OPAMPs circuit for MEMS MIC output, and they are looking for a lot of OPAMPs for this design. So please review the…
    • Answered

  • OPA2172: OPA2172 vs OPA1688 headphone amp performance

    Resolved
    Part Number: OPA2172 Other Parts Discussed in Thread: OPA1688 , Hi, i read the OPA1688 is very close to the OPA2172. in an output buffer application for an headphone amp, can I expect the same results with the 2172 compare to the 1688 when driving low impedance…
    • Resolved

  • OPA1688: Drift in DC output of a precision full-wave rectifier

    TI Thinks Resolved
    Part Number: OPA1688 Other Parts Discussed in Thread: OPA210 , OPA192 Hi everyone, I'm utilizing a precision full-wave rectifier ( www.ti.com/.../tidu030.pdf using OPA1688 and CUS10S40H3F) with post amplification ( non-inverting opamp using OPA210) to…
    • Answered

  • OPA1652: OPA1652 VS OPA1688

    Resolved
    Part Number: OPA1652 Other Parts Discussed in Thread: OPA1688 Hi TIer What about the different between OPA1652 and OPA1688. Is these two chip can drop in replace by each other? If can not , which parameter we need pay more attention to ? Thank you very…
    • Resolved
    • Answered

  • OPA1688: Current-generator stage oscillates, but not in simulation

    Resolved
    Part Number: OPA1688 Other Parts Discussed in Thread: OPA992 , TINA-TI Hi, I developed a current-generator stage using the OPA1688 device. The goal is to generate a current proportional to a analog voltage I can control. The current is driven to a 60-Ohm…
    • Resolved
    • Answered

  • OPA1688: Is the OPA1689 still enroute to release?

    Resolved
    Part Number: OPA1688 Almost done with the updates from 2015 forward, another one that shows up in a datasheet with no web folder, If the OPA1689 is almost there, what is the min 1k price in the web folder, This was from some time ago, https://e2e.ti.com…
    • Resolved

  • OPA1688: slew rate and voltage supply question

    TI Thinks Resolved
    Part Number: OPA1688 Other Parts Discussed in Thread: OPA1671 Hello expert, My customer has some questions need your confirmation. Thanks! We saw different slew rate in datasheet electrical parameter table(8 V/us) and table 3(4 V/us). May we know what…

  • OPA1652: Question on the rail performance

    Part Number: OPA1652 Other Parts Discussed in Thread: OPA1688 , OPA1656 , INA849 , JFE150 Tool/software: I'm designing the input stage for a guitar input and have identified the OPA1652 as a good candidate, but I have a question. The Vcm in the datasheet…

  • OPA1688: Input rail to rail

    TI Thinks Resolved
    Part Number: OPA1688 Other Parts Discussed in Thread: OPA1642 , , NE5532 , OPA1656 Hi expert, Device : OPA1688 and OPA1642 Can you provide any figure to show the input rail to rail when single supply use case like as following figure(NE5532)? Also, could…

Didn't find what you are looking for? Post a new question.