Filter by Reset

All
Forums (44)
  • Amplifiers (37)
  • Audio (3)
  • Automotive (Read-Only) (1)
  • C2000™︎ microcontrollers (1)
  • Power management (1)
  • Simulation, hardware & system... (1)
  • View all
Technical Articles (0)
Wikis (0)
Files (0)
Groups (0)
FAQ
  • Show only FAQs
Reply
  • Resolved
  • TI thinks resolved
  • Answer suggested
  • Has replies by TI employees
  • Has replies
Creation Date
  • Any
  • Past Week
  • Past Month
  • Past 3 Months
  • Past 6 Months
  • Past Year
From
To


Search tips
Showing 44 results View by: Thread Post Sort by

  • OPA2322: OPA2322AIDGKR

    TI Thinks Resolved
    Part Number: OPA2322 Tool/software: I'm using AD8226ARMZ-R7 from Analog devices with a gain of 1.99. The output of this Op-Amp is fed to a 6 pole 3KHz Butterworth anti-alising low pass filter having a unity gain formed by using OPA2322AIDGKR. I wanted…

  • OPA2322: TSV992IDT Alternative Device

    TI Thinks Resolved
    Part Number: OPA2322 Other Parts Discussed in Thread: OPA2323 Hello, Is there a TI alternative device for the TSV992IDT? Thanks, Ore.

  • OPA2322: Current Sensing signal conditioning

    TI Thinks Resolved
    Part Number: OPA2322 Other Parts Discussed in Thread: OPA4322 , OPA4323 , TLV9064 Customer would like to use OPA4322AIPWR for the 2nd source of the TLV9064IPWR. here list is comparison table. The OPA is being used for the signal conditioning for phase current…
    • Answered

  • OPA2322: input voltage noise in comparison to Q1 (automotive) equivalent

    Resolved
    Part Number: OPA2322 The OPAx322 electrical characteristics table in the datasheet shows input voltage noise of 2.8µVpp . The OPAx322-Q1 , shows 4.5µVpp . Both datasheets however, show the same chart (Figure 10) for input voltage noise. Can you…
    • Resolved
    • Answered

  • RE: TIDA-00316: Issue with the calculation of gains of opamp stage in the design

    Resolved
    1. Ok so you are suggesting a ref5030 + resistor divider + a buffer to be feed the ref 1.5 in the circuit. 2. My second question is still unanswered. Can I use a single ref for three such condition circuit as mentioned in ref design. As opa2322 has…
    • Answered

  • OPA2322: Query on Change in "Offset Voltage vs Temp" and "Open Loop Voltage Gain" Specification in Datasheet SBOS538F

    Resolved
    Part Number: OPA2322 Hi, I have a query on the changes made to the following parameters in the latest datasheet "SBOS538F" w.r.t. the previous revision of the datasheet " SBOS538E" . 1. Input Offset Voltage vs Temp (dVos/dT) : In dat…
    • Resolved

  • OPA2322-Q1: Wettable Flanks pin for OPA2322-Q1?

    TI Thinks Resolved
    Part Number: OPA2322-Q1 Other Parts Discussed in Thread: TLV9062 Hi All, My automotive customer is going to design a sensor automotive application using OPA2322-Q1. Does this p/n have wettable flanks pin? If so which exact package and code? If not, do…
    • Answered

  • OPA2322: Can I add a clamp on output of OPA2322 to prevent its output saturating.

    Resolved
    Part Number: OPA2322 Other Parts Discussed in Thread: UCC28950 Hello A customer wants to prevent the output of an error amplifier using the OPA2322 from saturating to shorten its recovery time. Vcc is 5V We don't want to use a simple anti-saturation diode…
    • Resolved
    • Answered

  • TINA/Spice/OPA2322: Need IBIS MODEL

    Resolved
    Part Number: OPA2322 Other Parts Discussed in Thread: TINA-TI Tool/software: TINA-TI or Spice Models Hello. We need OPA2322AIDGKR and OPA4322AIPWR IBIS MODEL. Please kindly provide it. Thanks~
    • Resolved
    • Answered

  • RE: OPA2322: Output issue

    Resolved
    Dear Kai. Good day. This is the same problem that we discussed before. We also try your suggestion before and just only one solution are worked. We cut off GND_B and GND_C then use a 0.01uF between GND_B and GND_C. The problematic OPA2322 are work. But…
1 2 3 4 5

Didn't find what you are looking for? Post a new question.