Search tips
Showing 22 results View by: Thread Post Sort by

  • OPA2325: Diode clamp for VCC

    TI Thinks Resolved
    Part Number: OPA2325 Other Parts Discussed in Thread: OPA2335 , ESD441 , Tool/software: Hi Expert, Customer add diode to clamp between VCC and GND. But with the temperature rise to +60C from 25C, the output is nonlinear. After removing the diode, the output…

  • OPA2325: Terminating an unused opamp

    TI Thinks Resolved
    Part Number: OPA2325 Tool/software: Dear Team, I was going through this article from TI regarding Unused opamp termination. It says that when Opamp is single supply you can use the termination given in below figure. Figure 1: When it is working Split…
    • Answered

  • OPA2325: Does there have an diode between IN+ & IN- of OPA2335

    Resolved
    Part Number: OPA2325 Other Parts Discussed in Thread: OPA4171 Hi team, In the DS of OPA2325,it says The OPAx325 incorporate internal electrostatic discharge (ESD) protection circuits on all pins. In the case of input and output pins, this protection primarily…
    • Resolved

  • OPA2325: OPA2325

    TI Thinks Resolved
    Part Number: OPA2325 Other Parts Discussed in Thread: TINA-TI , Dear Sir, We are using OPA2325IDR in the signal condition circuit. we are giving signal Input : 0 to 5 V DC and getting signal Output in between: 2.4 to 2.5 V DC, but the expected output should…
    • Answered

  • OPA2325: OPA2325 Recovery time

    Resolved
    Part Number: OPA2325 Other Parts Discussed in Thread: OPA325 I need an opamp that can quickly recover from output overload, since the input operates in a larger range than that l am interested in measuring. From the OPA2325 datasheet, table 6.7, I read…
    • Resolved
    • Answered

  • OPA2325: Latch-up test method and applied voltage

    Resolved
    Part Number: OPA2325 Hi Support Team. Please tell me whether OPA2325IDGKT is doing I-Test or Vsupply Overvoltage test when doing the latch-up test. Also, please tell me the applicable voltage during the test. Thanks,
    • Resolved

  • OPA2325: question

    Part Number: OPA2325 Other Parts Discussed in Thread: LM2903B , LM4041C , , OPA2376 Hello Experts, I would like to connect a shunt voltage reference (LM4041C) as voltage bias for comparator(LM2903B) to the output of OPA2325(or OPA2376) as shown in attached…

  • ADS127L21: Functional Safety AFE

    TI Thinks Resolved
    Part Number: ADS127L21 Other Parts Discussed in Thread: OPA2192 , OPA2325 , OPA2328 Tool/software: Hi TI Team I have two questions. 1. We plan to use the ADC in a safety PLC certified according to the IEC 61508 standard. We need to achieve SIL2 with a…
    • Answered

  • OPA2388: Capacitive load

    Resolved
    Part Number: OPA2388 Other Parts Discussed in Thread: OPA2328 , OPA2325 , , OPA2994 Tool/software: Dear Technical Support Team, I'm looking for alternative amp of AD8616. I selected OPA2388, OPA2328 and OPA2325, however AD8616 datasheet says "up to…
    • Resolved
    • Answered

  • OPA2325: Open-Loop Gain Matching

    Resolved
    Part Number: OPA2325 Other Parts Discussed in Thread: OPA2837 Hello, I'm looking to do a fairly simple transimpedance stage running at 10-20kHz, and I'd like to eliminate the error due to finite open loop gain, as far as possible. Datasheet shows typical…
    • Resolved

Didn't find what you are looking for? Post a new question.