Answered

• OPA2348-Q1: How to calculate the worst-case output error of this amplifier?

  

  Arie Li

  Resolved

  Part Number: OPA2348-Q1 Hi team, Could you please give some guidance about how to calculate the worst-case output error of this amplifier? Besides the accuracy of peripheral resistors, what parameters should be taken into consideration? How to use these…

  • Resolved

  • over 1 year ago
  • Amplifiers
  • Amplifiers forum
Answered

• OPA2348-Q1: [OPA2348-Q1] where I can find out Circuit Board Layout Techniques, SLOA089 ?

  

  Paul Kim

  Resolved

  Part Number: OPA2348-Q1 Hi Team OPA2348-Q1 mentioned "Refer to Circuit Board Layout Techniques, SLOA089" as below captured. BTW,,, customer cannot find out SLOA089 on TI website. may I get the document of SLOA089 ?

  • Resolved

  • over 4 years ago
  • Amplifiers
  • Amplifiers forum

• OPA4322-Q1: OP-AMP Behavior Under Off Condition

  

  Robert Liu1

  TI Thinks Resolved

  Part Number: OPA4322-Q1 Other Parts Discussed in Thread: OPA2348-Q1 , Hello TI Team, I am using both of the above op amps (OPA4322-Q1 and OPA2348-Q1). When these op-amps are off ( It is possible that (+) input voltage can go up to 16V through a 49.9k resistor…

  • over 1 year ago
  • Amplifiers
  • Amplifiers forum
Answered

• Circuit configuration for insulation

  

  user6246671

  Resolved

  Part Number: TIDA-01513 Other Parts Discussed in Thread: ISO7741 , ISO7710 , ISO7741-Q1 , ISO7761 , ISOW7841 , ADS1118 , , OPA2348 Hi Team I would like to use the insulation leak measurement circuit insulated from a 1000V battery. 1. We believe that the circuit…

  • Resolved

  • over 1 year ago
  • Simulation, hardware & system design tools
  • Simulation, hardware & system design tools forum
Answered

• OPA348-Q1: Questions about FIT(Failure In TIme)

  

  Paul Kim

  Resolved

  Part Number: OPA348-Q1 Other Parts Discussed in Thread: OPA4348-Q1 , , OPA2348-Q1 , OPA2348 , OPA4348 , OPA348 , TLV3701 , TLV3702 , TLV3704 Hi Team my Customer has the following questions about FIT for OPA348-Q1/OPA2348-Q1/OPA4348-Q1. may I expect your swift…

  • Resolved

  • over 3 years ago
  • Amplifiers
  • Amplifiers forum

• RE: TIDA-01513: TIDA-01513: Automotive High-Voltage and Isolation Leakage Measurements

  

  Rama Chandra Reddy Kambham

  Hello Vedran, Your understanding is correct. This issue can be solved by measuring and calculations systematically. As per TIDA-01513 we have 3 measurements. 1) Pack Voltage 2) ISO POS 3) ISO NEG We have two switches S1 and S2. Pack voltage might…

  • over 2 years ago
  • Simulation, hardware & system design tools
  • Simulation, hardware & system design tools forum

• [OPA348-Q1] what is the Abs Mas voltage for the differential input voltage ?

  

  Paul Kim

  Other Parts Discussed in Thread: OPA2348 , OPA4348-Q1 , OPA348 Hi Team inOPA348-Q1(OPA2348/OPA4348-Q1) datasheet, there is no comment on the Abs Mas voltage for the differential input voltage. may i know it ?

  • over 4 years ago
  • Amplifiers
  • Amplifiers forum

• OPA2348 Q Qualified in SOT23-8

  

  JasonHaedt

  Other Parts Discussed in Thread: OPA2348-Q1 , OPA2348 There appears to be an automotive qualified version of OPA2348 (OPA2348-Q1), but only in the 8-SOIC package. For space, I would like to use the SOT23-8 version of the non-qualified device. Can you…

  • over 9 years ago
  • Automotive (Read-Only)
  • Automotive Forum (Read-Only)
Answered

• OPA2348 Q Qualified in SOT23-8

  

  JasonHaedt

  Resolved

  Other Parts Discussed in Thread: OPA2348-Q1 , OPA2348 TI Team, There appears to be an automotive qualified version of OPA2348 (OPA2348-Q1), but only in the 8-SOIC package. For space, I would like to use the SOT23-8 version of the non-qualified device. …

  • Resolved

  • over 9 years ago
  • Amplifiers
  • Amplifiers forum

Didn't find what you are looking for? Post a new question.