Search tips
Showing 85 results View by: Thread Post Sort by
    Answered

  • OPA2376: Is this the best replacement for LMV821

    Resolved
    Part Number: OPA2376 Other Parts Discussed in Thread: OPA1611 , OPA1612 , OPA397 , OPA376 Hello, I am currently using the LMV821 as a microphone Preamp but it has a noisy output. I was looking into a fully differential opamp or a low noise opamp as potential…
    • Resolved
    • Answered

  • OPA2376: What is the maximum capacitor value can be driven by OPA2376 for low pass filter circuit?

    Resolved
    Part Number: OPA2376 Hello guys, One of my customers is evaluating OPA2376 with low pass filter circuit like the follow. https://www.avrfreaks.net/forum/why-simple-op-amp-low-pass-filter-does-not-work The customer parameters are the follow. R1 = 1k ohm…
    • Resolved

  • OPA2376-Q1: measured offset voltage is larger than calculated.

    TI Thinks Resolved
    Part Number: OPA2376-Q1 Other Parts Discussed in Thread: OPA2376 , Dear Specialists, My customer is evaluated OPA2376 in the customer's circuit, offset voltage is larger than the calculated value. I would be grateful if you could advise and make a friendship…

  • OPA2376: Does OPA2376 offset voltage become bigger than typical offset voltage spec when input pin (+IN,-IN)voltage is very low?

    TI Thinks Resolved
    Part Number: OPA2376 Hello guys, One of my customers is evaluating OPA2376 with low pass filter circuit like the follow.(But +IN=+100mV, V+=+5V, V-=0V) https://www.avrfreaks.net/forum/why-simple-op-amp-low-pass-filter-does-not-work The customer parameters…

  • OPA2376: OPA2376 ESD Rating

    TI Thinks Resolved
    Part Number: OPA2376 Hello, where can I find the ESD rating for HBM and CDM? I didn't find anything in the datasheet. Best regards Basti
    • Answered

  • OPA2376: Supply Missing with Input

    TI Thinks Resolved
    Part Number: OPA2376 Hi, I would like to have a question: What could happen, if the 3.3V supply of OPA2376 is missing, but input is supplied by some 10k Ohm to some volt? I am looking forward to your answer! Thank you and best regards, Ziming
    • Resolved
    • Answered

  • OPA2376: Device failure mode and limitation.

    Resolved
    Part Number: OPA2376 Hello According to the data sheet, the absolute rating of the input current to OUT pin is defined as up to 40mA. How long can be tolerated if a current about 50mA flows through the OUT pin? This is a question for circuit protection…
    • Resolved
    • Answered

  • OPA2376: Detail of abnormal behavior concerned with power supply failure

    Resolved
    Part Number: OPA2376 Hi team! Could you please let me know the behavior of your product in following cases? Case1: The IN+ and IN- pins are entered the signal with Voltage from 0.5V to 5.0V, without power supply. (V+ = V- = GND)) If the device will be…
    • Resolved
    • Answered

  • OPA2376-Q1: Alternative replacement for OPA2376QDGKRQ1 VSSOP

    Resolved
    Part Number: OPA2376-Q1 Other Parts Discussed in Thread: TLV2197-Q1 , LMV842-Q1 Hi There, As the part:OPA2376QDGKRQ1 VSSOP is out of stock, any suggestion for footprint compatible alternative part to replace? Thanks and Best Regards Dong
    • Resolved
    • Answered

  • OPA2376: Input Differential Mode Voltage Range

    Resolved
    Part Number: OPA2376 Other Parts Discussed in Thread: TLV9062 In the d/s, it specifies the input common mode voltage range, how about the input differential voltage range? Thanks. Regards Brian W
    • Resolved

Didn't find what you are looking for? Post a new question.