Search tips
Showing 16 results View by: Thread Post Sort by
    Answered

  • OPA2607: Is there a way to know the release dates of your operational amplifier products?

    Resolved
    Part Number: OPA2607 Other Parts Discussed in Thread: OPA2810 , , OPA2328 Tool/software: I would like to know the release dates of OPA2607, OPA2810, and OPA2328.
    • Resolved

  • RE: OPA2607: shorting V and V-

    Hi Roy, I attached the file below. I took a guess as to how the transducer is configured which is represented by CD. Once again simulation will at times not paint a clear picture as to what will affect the stability especially when working with components…
    • Answered

  • OPA2607-Q1: The stability of OPA2607 with high capacitor load

    Resolved
    Part Number: OPA2607-Q1 Other Parts Discussed in Thread: OPA2607 , OPA607 , TINA-TI Hi I want to use OPA2607 for current sensing in sensorless motor control application. In the datasheet, opa x607 is not unity-stable with min-gain = 6V/V. Also the Riso is…
    • Resolved

  • OPA2607-Q1: Where is PSPICE model for this device located?

    TI Thinks Resolved
    Part Number: OPA2607-Q1 Other Parts Discussed in Thread: OPA2607 , OPA607 Hello, My customer would like simulate with OPA2607-Q1, but I cannot located the pspice model on the product page. Can you please tell me where this model is located so that the…

  • OPA2607-Q1: Voltage Follower Stability and Dynamic Range

    Part Number: OPA2607-Q1 Other Parts Discussed in Thread: TINA-TI I was planning to use the OPA2607-Q1 as a voltage follower. Apparently, after injecting a signal from 0 to 5V, it shows that the OPAMP saturates to around 4V. Is there any specific reason…
    • Answered

  • OPA2607: OPA2607

    Resolved
    Part Number: OPA2607 Other Parts Discussed in Thread: OPA607 , TINA-TI Hi TI, I noticed a nice operational amplifier, which is new in your assortment - OPA2607. Due to its characteristics, it would be quite applicable in my future projects. Is it possible…
    • Resolved

  • OPA2607: Calculate the GBW

    Part Number: OPA2607 Dear Team Here is Kevin from Delta Taiwan team I would like to propose OPA2607 to replace MAX4128 Customer is calculating the GBW for the PFC current sense circuit. Vth is the OP input from the shunt resistor, which is 100kHz sine…

  • RE: OPA2626: Strange behavior of OPA2626

    Hello, Could you try simulating your circuit with OPA810, TLV365 and OPA607 models? I am curious if the ADC driving focus on the OPA2626 device makes its model behave oddly in non-ADC driving configurations. Was there a particular reason you were looking…

  • OPA2171: Output doesn't match the input in certain working condition

    TI Thinks Resolved
    Part Number: OPA2171 Other Parts Discussed in Thread: OPA2607 , OPA2991 , OPA2992 , OPA2990 Hi team, Customer use OPA2171 to sample the primary current in LLC topology. They use to parallel LLC to extend the power, and OPA2171 is used to sample two primary…

  • [FAQ] [H] Frequently Asked Questions - High Speed Amplifiers Selection Guide - CMOS Input Amplifiers

    Frequently Asked Questions: Amplifiers >> High Speed Amplifiers >> HSA Selection Guide >> CMOS Input Amplifier Selection Guide JFET Input Bipolar Input CMOS Input FDAS Power Amps VGAs TIAs Introduction: FET/CMOS…

Didn't find what you are looking for? Post a new question.