Filter by Reset

All
Forums (68)
  • Amplifiers (62)
  • Simulation, hardware & system... (4)
  • Audio (1)
  • Power management (1)
  • View all
Technical Articles (1)
Wikis (0)
Files (0)
Groups (0)
FAQ
  • Show only FAQs
Reply
  • Resolved
  • TI thinks resolved
  • Answer suggested
  • Has replies by TI employees
  • Has replies
Creation Date
  • Any
  • Past Week
  • Past Month
  • Past 3 Months
  • Past 6 Months
  • Past Year
From
To


Search tips
Showing 68 results View by: Thread Post Sort by

  • OPA2810: Parameters in datasheet check

    TI Thinks Resolved
    Part Number: OPA2810 Tool/software: Hi TIer There are two parameters that have not been found in datasheet. Could you give me some suggestion? 1, open-loop gain with temperature change 2, common mode voltage input range Thank you very much.
    • Answered

  • OPA2810: Can I supply OPA2810 and OPA356 with asymmetric power rail?

    Resolved
    Part Number: OPA2810 Other Parts Discussed in Thread: OPA356 I have OPA2810 and OPA356. I'd like to configure OPA356 as I-V converter(Photodiode) and OPA2810 as second non invert or invert amplifier(integrator, G=10) AFAIK, some OP-AMPs supplied …
    • Resolved

  • OPA2810: Is there any chip can replace AD8066?

    Part Number: OPA2810 Other Parts Discussed in Thread: OPA2863A Hi TIer When I recommend the customer to use OPA2810 replace AD8066. customer concern the cooling capacity of OPA2810. Customer prefer the chip with thermal pad. So could you provide me with…
    • Answered

  • OPA2810: Maximum differentiual input voltage/ input current

    Resolved
    Part Number: OPA2810 Other Parts Discussed in Thread: NE5534 Hi Experts, Seeking your assistance: I build an transimpedance amplifier circuit with the OPA2810. In a special condition, the inverting input pin is (quasi) connected to the positive supply…
    • Resolved

  • OPA2810: Asymmetric power supplied rail and little lower power supplied rail

    TI Thinks Resolved
    Part Number: OPA2810 Other Parts Discussed in Thread: ADS7961 My system diagram as this picture: I discover OPA2810 Vs of " Recommended Operating Conditions" which minimum is 4.75v. My LOD(TPS7A2045) only provide 4.5V. I tried simulation G…
    • Answered

  • OPA2810: Bulk capacitance Guidance for Sharing Amongst Amplifiers

    Resolved
    Part Number: OPA2810 Hello, In the OPA2810 it recommends using a larger capacitor for the power pins and mentioned that it can be shared among several devices. Do we have any more details on constraints for sharing? In our design we have a large copper…
    • Resolved

  • Understand the working of OPA2810 as a buffer

    Part Number: OPA2810IDGKR Hi TI, We are looking for an alternate to OPA2863. We came across OPA2810 which has required slew rate and package with pin to pin matching. What my query is how is it different from OPA2863. Can I use it as a buffer for a…

  • OPA2810: open loop gain graph on figure 44

    TI Thinks Resolved
    Part Number: OPA2810 Hi Team, we would like to seek your assistance on the graph translation since the plot starts near 180 instead of 0. Hoping for your inputs. Thank you. -Mark

  • PSPICE-FOR-TI: Monte Carlo analysis of OPA2810 with PSpice for TI

    Part Number: PSPICE-FOR-TI Other Parts Discussed in Thread: OPA2810 Hi, What parameters can be set when performing Monte Carlo analysis of OPA2810 with PSpice for TI? Thanks,

  • OPA2810: Input voltage range

    TI Thinks Resolved
    Part Number: OPA2810 We are planning on using OPA2810 in our Analog IO card. I need some clarifications. Our requirement is +/-10V single ended. We will be using +/-12V as Vs+ and Vs- supply voltages. I am a little bit concerned because allowable input…
1 2 3 4 5 »

Didn't find what you are looking for? Post a new question.