Search tips
Showing 31 results View by: Thread Post Sort by

  • LMV321: The output voltage is strange.

    TI Thinks Resolved
    Part Number: LMV321 Other Parts Discussed in Thread: OPA310 Tool/software: The LMD321IDCKR operational amplifier is used in the voltage follower circuit. If 4.2 V is input and 40 mA flows to the output, the output will be 1.5~2.5 V. The voltage waveform…
    • Answered

  • XTR200: XTR200, 0-10V output.

    Resolved
    Part Number: XTR200 Other Parts Discussed in Thread: TLV9001 , AMC1351 , OPA310 , OPA320 Hi guys. I'm trying to build an isolated 0-10V circuit using an XTR200 and an AMC1351QDWVRQ1. Schematic is as follows: Circuit is working good but with the…
    • Resolved

  • OPA607: OPA607

    Part Number: OPA607 Other Parts Discussed in Thread: OPA835 , OPA376 , , OPA310 , OPA323 , OPA322 Tool/software: Is there any workable pspice code of any of your general purpose amplifiers? I am working in cadence with the pspice models and none of your…
    • Answered

  • TLV9001: Is there ESD protection diodes on IN+ or IN- pins?

    Resolved
    Part Number: TLV9001 Other Parts Discussed in Thread: LM321LV , OPA2348 , OPA2310 , OPA348 , OPA310 Tool/software: Hello, TI expert I found that there are protection diodes on OPA like LM321LV, but I need an OPA without those diodes between IN pins…
    • Resolved
    • Answered

  • OPA170: Siemens is looking for an alternative without ESD protection diodes

    Resolved
    Part Number: OPA170 Other Parts Discussed in Thread: OPA310 Hi Team, Siemens is looking for an alternative for OPA170 without ESD protection diodes. Do we have such a device available? Thanks, Stefan
    • Resolved

  • TLV9001: Input impedance of TLV9001

    TI Thinks Resolved
    Part Number: TLV9001 Other Parts Discussed in Thread: OPA310 , OPA2310 Hi team, I would like to check with you, if we have the data for input impedance for TLV9001? I could see OPA310 has the both resistance//capacitance but I can only find input…
    • Answered

  • TLV341: Up rail voltage dropout above the spec in datasheet

    Resolved
    Part Number: TLV341 Other Parts Discussed in Thread: OPA171 , OPA170 , OPA310 Tool/software: Hi, We are using a a TLV341 in a follower configuration. The amplifier is powered with a 3V LDO, decoupled with 100nF X7R resistor. When I put a 3v source…
    • Resolved

  • RE: INA592: Back Powering Issue in 3-Wire Transmitter Design

    Hi Doudu, Sorry for the delay here, I was out-of-office yesterday. I see, I will have to think about how we could fix this issue, as it would likely require different buffer amps. We do have the OPA310, which does include fail-safe input ESDs that prevent…
    • Answered

  • TPS386000: TPS386000 negative input voltage/current absolute maximum ratings for SENSE and VREF pins

    Resolved
    Part Number: TPS386000 Other Parts Discussed in Thread: OPA310 , TPS3700 , TPS3701 , TPS7A33 Tool/software: Hi, I am planning on using TPS386000 voltage supervisor on an application involving +/- 18 V bipolar supplies, so, a variant of the circuit…
    • Resolved

  • TLV9041: Higher current consumption than expected

    TI Thinks Resolved
    Part Number: TLV9041 Other Parts Discussed in Thread: TLV7031 , OPA310 Tool/software: Hi team, I am using TLV9041 in my design (see the attached schematic). TLV9041 is used as a non-inverting amplifier. The input to the Op amp is a 0-3.3V 1KHz 5…

Didn't find what you are looking for? Post a new question.