TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 28 results View by: Thread Post Sort by
    Answered
  • OPA37: OPA37

    Donald Wright
    Donald Wright
    Resolved
    Part Number: OPA37 Tool/software: My question is simple. What do I do if the Trimming pins 8 and 1 are not use for my application ? I could not find any information about it in the specification/data sheet. Thanks. Donald.
    • Resolved
    • 3 months ago
    • Amplifiers
    • Amplifiers forum
  • OPA37: Need two groung level to simulation

    Hank hung
    Hank hung
    TI Thinks Resolved
    Part Number: OPA37 Tool/software: I need to simulate the charge circuit. That's a charge control circuit series connecting a cap. But I can't simulate normally. Vshunt node keep sinking currnet through R9、R7、R13 to the ground So the OPAs can't work…
    • 7 months ago
    • Amplifiers
    • Amplifiers forum
  • OPA37: Similar product with OPA37

    Li Chen92
    Li Chen92
    Part Number: OPA37 Other Parts Discussed in Thread: OPA4227 , OPA4228 Hi TI expert Please help to find a 4 channel amp and similar with OPA37. Best regards, Thomas
    • over 4 years ago
    • Amplifiers
    • Amplifiers forum
  • Answered
  • RE: TINA/Spice: PCB Layout design of audio pre amplifier using OPA37 and OPA2111

    Parag chourey
    Parag chourey
    Resolved
    Thanks Sir Regards Parag
    • over 6 years ago
    • Amplifiers
    • Amplifiers forum
  • Answered
  • OPA37: Need to know differential mode input impedance (capacitance) to design for feedback capacitor

    Michael Robinson70
    Michael Robinson70
    Resolved
    Part Number: OPA37 I am looking to design a transimpedance amplifier for use in a pulse oximeter, I'd like to design not only for feedback resistor but also for the feedback capacitor but for this I need to know the differential input impedance, it is…
    • Resolved
    • over 7 years ago
    • Amplifiers
    • Amplifiers forum
  • Hydrophone preamplifier design using OPA37

    Vrinda Menon
    Vrinda Menon
    TI Thinks Resolved
    Other Parts Discussed in Thread: OPA37 , OPA27 I need a hydrophone preamplifier circuit with frequency response in the range of 2Hz to 30 Khz with single voltage supply. The data sheet of OPA37 contains a hydrophone preamp for EDO6166 transducer with…
    • over 12 years ago
    • Audio
    • Audio forum
  • Active Filter using OPA37

    AlB
    AlB
    Other Parts Discussed in Thread: OPA37 , OPA227 , OPA27 Hello, I have designed an active filter using a OPA37 as shown below, but it causes oscillation at the output near 400Mhz frequency. I have tried increasing the feedback resistance t further increase…
    • over 13 years ago
    • Amplifiers
    • Amplifiers forum
  • Answered
  • RE: PCB layout check.

    Parag chourey
    Parag chourey
    Resolved
    Hello sir, I attached the solder mask file in the attachment. Kindly see and suggest any correction if any. In this file U3, U4, U17 and U19 are the OA2111 and rest are OPA37.
    • over 6 years ago
    • Simulation, hardware & system design tools
    • Simulation, hardware & system design tools forum
  • Answered
  • RE: OPA637: OPA637 distortion problem

    Thomas Kuehl
    Thomas Kuehl
    Resolved
    Hello Pei, Michael brings up valid points about the phase margin that needs to be assessed and assured when attempting to apply an undercompensated Op amp such as the OPA37 in a TIA application circuit. I suspect there is a stability issue with one…
    • over 6 years ago
    • Amplifiers
    • Amplifiers forum
  • Answered
  • RE: OPA627: Paralleling 2 op amps to reduce noise file

    Thomas Kuehl
    Thomas Kuehl
    Resolved
    Hello Rhandhir, Unfortunately, the original 2012 e2e post wasn't specific regarding the location of that file. The e2e PDF access may have worked differently then, compared to today and that may be the reason it is no longer accessible. I receive the…
    • over 6 years ago
    • Amplifiers
    • Amplifiers forum
>

Didn't find what you are looking for? Post a new question.

  • Ask a new question