TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel

Because of the Thanksgiving holiday in the U.S., TI E2E™ design support forum responses may be delayed the week of November 23.



Search tips
Showing 12,576 results View by: Thread Post Sort by
    Answered
  • RE: IWRL6432BOOST:Complex Data/ Phase Reconstruction

    Tom Lackinger
    Tom Lackinger
    Resolved
    Hello Zigang, thank you for your reply. However, I feel that my original question was not fully answered. To clarify: I understand that the range FFT output is complex due to the real input being processed, and that only the first half is used…
    • over 1 year ago
    • Sensors
    • Sensors forum
  • RE: IWR6843AOPEVM: High Speed Detection From Fixed Point

    Santosh Krishnan
    Santosh Krishnan
    Hello Shikhar. shikhar sharma said: Velocity Measurement Capability Is the IWR6843 capable of reliably estimating radial Doppler velocity for a small, high-speed, non-metallic target over short-to-medium ranges? Yes this is possible…
    • 10 months ago
    • Sensors
    • Sensors forum
  • LMX2595: Single frequency band problem

    Ian Carmack
    Ian Carmack
    Part Number: LMX2595 Tool/software: How sensitive is the RF-Out to pull up broadband impedance? I have a design that we use for calibration, it uses the full range of the LMX2595 range. We have one specific range of frequencies that don't work. They…
    • over 1 year ago
    • Clock & timing
    • Clock & timing forum
  • Answered
  • AWR2243: MMWCAS-DSP-EVM: Flat target only reflects when its surface faces the radar directly; signal disappears with a 1-2 degree tilt - is this normal?

    Steve Huang
    Steve Huang
    Resolved
    Part Number: AWR2243 Other Parts Discussed in Thread: TIDEP-01012 , Hi, I am using MMWCAS-RF-EVM (4-chip cascade, 12 TX x 16 RX) + MMWCAS-DSP-EVM to detect my cell phone in 2m. The settings are as below: Chirp / Frame configuration - ADC samples per chirp…
    • Resolved
    • 4 months ago
    • Sensors
    • Sensors forum
  • RE: AWRL1432BOOST: AWRL1432BOOST Visualizer SOP Connection Issue

    ? ??
    ? ??
    Hi Kundan, Thanks for the suggestion regarding the silicon replacement. However, before we proceed with replacing the silicon to the RTM version, we need to verify that the EVM board itself is fully functional. To do this, we need to validate the…
    • 9 months ago
    • Sensors
    • Sensors forum
  • RE: TMAG5170-Q1: TMAG5170 raw ADC values are not stable

    Scott Bryson
    Scott Bryson
    Dheeraj, Sure, I understand. In the 100mT range, the output scales by about 326LSB/mT, and the input referred noise can be up to 34uT RMS at room temperature. Since RMS noise represents 1 sigma, we would multiply by 6.6 to approximate the peak output…
    • 4 months ago
    • Sensors
    • Sensors forum
  • MMWCAS-RF-EVM: Changing the radar configurations

    kauthar
    kauthar
    TI Thinks Resolved
    Part Number: MMWCAS-RF-EVM Other Parts Discussed in Thread: AWR2243 , AWR1843 Tool/software: Hi, I'm using the MMWCAS-RF-EVM along with the MMWCAS-DSP-EVM to collect data using mmWave Studio 3.0.0.14. The MMWCAS-RF-EVM is composed of AWR2243 radars…
    • over 2 years ago
    • Sensors
    • Sensors forum
  • RE: IWR6843AOPEVM: Lateral (cross-range) spatial resolution using IWR6843AOP with 500MHz Bandwidth

    Abhishek Karkisaval
    Abhishek Karkisaval
    Hi, You can refer to the FCC regulations which is applicable for India also now. For chirp configuration and range, please refer to TI sensing estimator https://dev.ti.com/gallery/view/mmwave/mmWaveSensingEstimator/ver/2.5.1/ Regards
    • 11 months ago
    • Sensors
    • Sensors forum
  • RE: IWR6843AOP: DPU_RangeProcHWA_process processing time measurement

    eric rk
    eric rk
    Hello Sharan, Many thanks for your feedback. 1.If I use numloops = 2, how does it work? I did use single RX, single TX, and estimated only the range on the HWA by downchirp. Does it work like this? HWA processing time = ~ 137.61 μs. Is Chirp's processing…
    • over 1 year ago
    • Sensors
    • Sensors forum
  • Answered
  • RE: TPS7B84-Q1: Accuracy guarantee at worst case.

    Eduardo Linares
    Eduardo Linares
    Resolved
    Hi Manmohan, There isn't enough information here. What is your VIN range and ambient temperature? We can over-estimate the error by assuming a 0.2% change with load reg and another 0.2% for line reg, or we could consult the graphs in the datasheet for…
    • 4 months ago
    • Power management
    • Power management forum
<>

Didn't find what you are looking for? Post a new question.

  • Ask a new question