Answered

• SN65HVD230: The RS pin must be pulled down to receive the correct bus data

  

  Amy Luo

  Resolved

  Part Number: SN65HVD230 Hi team, The customer's current situation is: SN65HVD230 in listen only state, after receiving the RX pin signal, STM32 MCU must first pull the RS pin down can receive the correct bus data. If the customer's this node is…

  • Resolved

  • 1 month ago
  • Interface
  • Interface forum
Answered

• ISO1050: can ISO1050 communicate with SN65HVD230

  

  Sunny Qin

  Resolved

  Part Number: ISO1050 Other Parts Discussed in Thread: SN65HVD230 , Hi Team, I saw ISO1050 and SN65HVD230`s output voltage level is different as below: ISO1050 SN65HVD230 So I am wonder can ISO1050 communicate with SN65HVD230? Thanks. Regards, Sunny

  • Resolved

  • 2 months ago
  • Isolation
  • Isolation forum
Answered

• SN65HVD230: CAN isolator (from CAN to CAN) having problems communicating two ways

  

  Nakib Ramani

  Resolved

  Part Number: SN65HVD230 Hi, I am trying to make a CAN isolator (from CAN to CAN), I am using the can transceiver SN65HVD230 to convert from CAN to TX, RX, and then an isolated CAN transceiver to convert it back to CAN. But when I try sending a CAN message…

  • Resolved

  • 3 months ago
  • Interface
  • Interface forum

• SN65HVD230: Bus maximum voltage

  

  Carloalberto Torghele

  Part Number: SN65HVD230 Other Parts Discussed in Thread: SN65HVD233 Hi, we would like to use your SN65HVD230D in the following manner. Mode 1 - normal can bus mode: of course SN65HVD230D is ok. Mode 2 - Can bus transmission disabled: on the BUS there will…

  • 6 months ago
  • Interface
  • Interface forum

• WEBENCH® Tools/SN65HVD230: SN65HVD230 signal line capacitance selection

  

  user6342742

  TI Thinks Resolved

  Part Number: SN65HVD230 Tool/software: WEBENCH® Design Tools I was using SN65HVD230DR and found that there is no description of C7, C8, C9 in the data manual, and I have not found the corresponding description after consulting some materials. How to choose…

  • 10 months ago
  • Simulation, hardware & system design tools
  • Simulation, hardware & system design tools forum

• WEBENCH® Tools/SN65HVD230: SN65HVD230 TVS recommended

  

  user6342742

  Part Number: SN65HVD230 Tool/software: WEBENCH® Design Tools What are the recommendations for TVS corresponding to SN65HVD230? The package should be close to SOD-923F.

  • over 1 year ago
  • Simulation, hardware & system design tools
  • Simulation, hardware & system design tools forum

• SN65HVD230：1:4 CAN solution

  

  Miranda Gu

  Answer Suggested

  Part Number: SN65HVD230 Hi team, My customer is looking for 1:4 3.3V CAN solution, 1 input, 4 outputs are same, to drive 4 CAN devices. Could you please recommend a solution?

  • 9 months ago
  • Interface
  • Interface forum
Answered

• SN65HVD230: CANH and CANL pins protection

  

  Jejomar Ildefonso

  Resolved

  Part Number: SN65HVD230 Other Parts Discussed in Thread: SN65HVD234 , SN65HVD233 , SN65HVD235 Hi Team, Our customer is using the SN65HVD230 for their sensor design. They intend to bring the CANH and CANL from the SN65HVD230 outside the sensor for the user…

  • Resolved

  • 10 months ago
  • Interface
  • Interface forum

• SN65HVD230: Equivalent Input and Output Schematic Diagrams

  

  Michiaki Tanii

  TI Thinks Resolved

  Part Number: SN65HVD230 Hello team, Our customer point out that there is a gap between CANH/L of block diagram at page 1 and the circuit at page 18 as following. Is it true the circuit for CANH and CANL outputs at page 18 ? It shows totem pole circuit…

  • 10 months ago
  • Interface
  • Interface forum

• SN65HVD230: c The surface of the product is white

  

  user6350528

  Part Number: SN65HVD230 Hi Team The surface of the product we received is white. Is this the normal production process? Does it affect usage?

  • 9 months ago
  • Interface
  • Interface forum

Didn't find what you are looking for? Post a new question.