Answered

• SN74HCS32: SN74HCS32PWR Reliability Data MTTF

  

  Michael Reilly

  Resolved

  Part Number: SN74HCS32 Tool/software: Hello, Where can I find the reliability data for the SN74HCS32PWR? Specifically I am looking for the MTTF. Thanks.

  • Resolved

  • 11 months ago
  • Logic
  • Logic forum
Answered

• SN74HCS32-Q1: Spice model

  

  Michael Daimer

  Resolved

  Part Number: SN74HCS32-Q1 Other Parts Discussed in Thread: SN74HCS32 Hello Logic Team, can you provide a Spice model of SN74HCS32? Preferred unencrypted model. Thanks and best regards, Michael

  • Resolved

  • over 1 year ago
  • Logic
  • Logic forum

• SN74HCS32-Q1: Spice model

  

  Michael Daimer

  Part Number: SN74HCS32-Q1 Other Parts Discussed in Thread: SN74HCS32 Hello Logic Team, can you provide a Spice model of SN74HCS32? Preferred unencrypted model. Thanks and best regards, Michael

  • over 1 year ago
  • Logic
  • Logic forum

• SN74HCS32-Q1: Request to Functional safety FIT value(SN29500-2)

  

  An jinyoung

  Part Number: SN74HCS32-Q1 Other Parts Discussed in Thread: INA148-Q1 , TCAN1042-Q1 I inquire about the functional safety FIT(Application FIT Rate) value for the device below. Standard is SIEMENSE SN29500-2. (it is not a request for a JEDEC-based technical…

  • over 2 years ago
  • Logic
  • Logic forum
Answered

• SN74HCS32: Maximum Load Capacitance

  

  Shinichi Inoue

  Resolved

  Part Number: SN74HCS32 Dear Specialists, My customer is considering sN74HCS32 and has a question. I would be grateful if you could advise. --- According to the datasheet P.10 load capacitance is able to drive until 70pF. Could we understand…

  • Resolved

  • over 4 years ago
  • Logic
  • Logic forum

• SN74HC32: difference between SN74HC32NS and SN74HC32NSR

  

  J-ZHOU8

  TI Thinks Resolved

  Part Number: SN74HC32 Other Parts Discussed in Thread: SN74HCS32 Tool/software: Hello experts Hope this finds you well. Basically, I think these 2 are same products. Right please? The only difference is only reel or not. But if these 2 are different…

  • 10 months ago
  • Logic
  • Logic forum
Answered

• CAN−bus Extender

  

  samed a

  Resolved

  Other Parts Discussed in Thread: SN74HCS32 Hello, I want to Canbus extender. I was using AMIS42700. However, at the moment AMIS42700 is unfortunately not produced. I use ICs such as TJA1050 or TJA1448. I ran 4 nodes with the following arbitration circuit…

  • Resolved

  • over 3 years ago
  • Interface
  • Interface forum

• SN74AUP1G32: Output(Y) abnormal Waveform Issue

  

  Vincent Lin

  TI Thinks Resolved

  Part Number: SN74AUP1G32 Other Parts Discussed in Thread: SN74HCS32 , SN74AUP1G17 , SN74LVC1G97 , SN74AUP3G17 , SN74AUP1G125 Dear Sir: Regarding the output(Y) of SN74AUP1G32 (Low-Power Single 2-Input Positive-OR Gate) abnormal Waveform Issue. According…

  • over 3 years ago
  • Logic
  • Logic forum
Answered

• RE: SN74HC32: Do I need current limiting resistor on input?

  

  Clemens Ladisch

  Resolved

  CMOS inputs have a very high impedance; a series resistor would have no noticeable effect. You can connect the inputs directly to V CC or GND or a logic output. Please note that the clamp current limit is specified for voltages outside the recommended…

  • over 5 years ago
  • Logic
  • Logic forum

• RE: 4input Orgate || AEC qualified

  

  Clemens Ladisch

  There is no such automotive-qualified device. You have to combine multiple OR gates; 3× 3 inputs (SN74HCS4075-Q1), or 4× 2 inputs (SN74LVC32A-Q1, SN74HCS32-Q1, SN74AHC32Q-Q1, SN74LV32A-Q1).

  • over 2 years ago
  • Logic
  • Logic forum

Didn't find what you are looking for? Post a new question.