Search tips
Showing 309 results View by: Thread Post Sort by

  • THS4541: Simulation unmatched

    Part Number: THS4541 Other Parts Discussed in Thread: TINA-TI Hello, I was simulating the loop gain of an amplifier with the part number THS4541. I followed the tutorial step by step using TINA-TI, but the output I obtained was not similar to the one…
    • Answered

  • THS4541: Applications that use THS4541 to reduce signal noise by reducing signal noise

    Resolved
    Part Number: THS4541 Tool/software: THS4541 can I configure the gain to be reduced by 2x, and only the resistor magnified by 2x is recommended in the datasheet, can I swap the 402 Ohm and 191 Ohm resistance values of Rf and Rg to achieve the purpose of…
    • Resolved
    • Answered

  • THS4541: VCM current consumption

    Resolved
    Part Number: THS4541 Other Parts Discussed in Thread: ADS5296A Tool/software: Hi, pls. provide the current consumption of the VCM connected to THS4541. one pin of the ADS5296A drive 8 units of the THS4541 and I need to know if additional op amp…
    • Resolved

  • THS4541: ths4541

    TI Thinks Resolved
    Part Number: THS4541 Other Parts Discussed in Thread: ADC3644 Hi Nick, we are getting input of 1-45MHz frequency of I data to our unit and then we are connecting to FDA and then to ADC . final our application is to process a signal in 1-45mhz range…

  • THS4541: THS4541

    Part Number: THS4541 Hi, Please find the below part: P/N-THS4541 Kindly share the deferential length marching details above part. Best Regards, Nanjegowda

  • THS4541: THS4541

    TI Thinks Resolved
    Part Number: THS4541 Other Parts Discussed in Thread: BUF634 , OPA863 Hi, I need support about this component. We have to convert a single-ended pulse 0-3.3V Tduration =15ns f=50kHz (generated by a microcontroller and a high speed TTL buffer) into…
    • Answered

  • THS4541: THS4541IRGTR high impedance configuration

    Resolved
    Part Number: THS4541 Tool/software: We are using a differential amplifier THS4541IRGTR and we need to know if it is possible to use it with high input impedance configuration, using the resistances configuration as attached picture. Moreover, we'd like…
    • Resolved
    • Answered

  • THS4541: Setting Vocm to 1.4V using pull-down resistor

    Resolved
    Part Number: THS4541 Tool/software: Hello all, In my application, I use the THS4541 in a single-ended to differential configuration. The FDA is connected to a DAC, and both use a 3.3V single supply. The differential signals are typically biased…
    • Resolved
    • Answered

  • THS4541: Output resistance limit for linear operation

    Resolved
    Part Number: THS4541 Other Parts Discussed in Thread: TINA-TI Tool/software: Hello I have noticed that the output of the THS4541 is noticeably non-linear when fixing the common mode input voltage and sweeping the differential voltage when there are…
    • Resolved
    • Answered

  • THS4541: Assistance with FDA Bessel MFB LPF Design

    Resolved
    Part Number: THS4541 Other Parts Discussed in Thread: TINA-TI , THS4561 I am designing a 2nd-order Bessel MFB low-pass filter using the THS4541 with the following specifications: Passband: DC to 100 kHz with minimal insertion loss and group delay…
    • Resolved

Didn't find what you are looking for? Post a new question.