TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 25 results View by: Thread Post Sort by
    Answered
  • RE: INA219: BUS voltage SPEC confirmation

    Mitch M
    Mitch M
    Resolved
    Hello Stanly, You are correct, the INA219 does not support that BUS voltage. If the INA219 is still needed, then here are a couple of design guides that can be used to to make this work: https://www.ti.com/tool/TIDA-00528 https://www.ti.com/tool…
    • over 1 year ago
    • Amplifiers
    • Amplifiers forum
  • Answered
  • RE: Suggest any DC Voltage & DC Current Measurement cards ??

    Selvaganesh Venkatesan
    Selvaganesh Venkatesan
    Resolved
    Hai Andrews !!! 1. May i Know the maximum threshold current that TIDA-00528 (40V to 400V Uni-directional Current/Voltage/Power Monitoring Reference Design) board can withstand ??? For my applications, current rating is 25A respectively.., 2. As i…
    • over 4 years ago
    • Power management
    • Power management forum
  • RE: TMCS1108: Can TMCS1108 measure 10uA to 3A?

    Joe Vanacore
    Joe Vanacore
    Hi Jimmy, I missed the uA. Thank you for catching that and apologies for the mistake. I would not use the TMCS1108 as the offset error is in the mA range and would not allow for accurate measurements in uA. We do have the new TMCS1123 with higher…
    • over 1 year ago
    • Sensors
    • Sensors forum
  • RE: INA229: Extending Bus voltage range to 400V

    Mitch M
    Mitch M
    Hey Lukas, Oh, I also forgot about this reference design: https://www.ti.com/tool/TIDA-00528 . This use case is specific to 400V, but does use high side. In this design they chose to go with the voltage divider over any opamp method, so it will still…
    • over 3 years ago
    • Amplifiers
    • Amplifiers forum
  • RE: TIDA-00951: TIDA-00951 High voltage current sensor

    Carolus Andrews
    Carolus Andrews
    Mohammad, We have a few ways to do this. The first is with our digital product line, which could pass the signal via I2C to the microcontroller: TIDA-00528 You can also do this with our analog devices using a clamping diode: TIDA-00332 We also…
    • over 5 years ago
    • Simulation, hardware & system design tools
    • Simulation, hardware & system design tools forum
  • Answered
  • RE: INA226: INA226

    Mayrim Verdejo
    Mayrim Verdejo
    Resolved
    Hi Amy, Forgot to add. If customer prefer to use high side please refer them to the TIDA-00528.
    • over 8 years ago
    • Amplifiers
    • Amplifiers forum
  • Answered
  • RE: INA220 - 9.2.4 Typical Application: 48-V Telecom Current/Voltage/Power Sense

    Peter Iliya
    Peter Iliya
    Resolved
    Hello Neel, Thanks for posting to the forum. Here is the application note for the circuit shown in Figure 32: http://www.ti.com/tool/TIDA-00528 The Rshunt and RL set the gain of the circuit. The Rshunt is applied acros the RG resistor to create an…
    • over 5 years ago
    • Amplifiers
    • Amplifiers forum
  • RE: LMP92064 - Current/Power Monitor

    Mayrim Verdejo
    Mayrim Verdejo
    Hi Phrahlad, I missed the application recommendation! If your customer is willing to use the external components then you can recommend LMP92064. I would recommend they try this on the lab before designing any layout. This is just a reference design…
    • over 8 years ago
    • Amplifiers
    • Amplifiers forum
  • Answered
  • RE: INA226: Use of to measure current and voltage of + and - rails in an audio amplifier

    Mayrim Verdejo
    Mayrim Verdejo
    Resolved
    Hi Ian, I had an idea of modifying my design for positive rail but it would work only if you only needed to measure current and not Vbus and power. So this would not work for your application. Unfortunately we have not design yet a circuit that…
    • over 8 years ago
    • Amplifiers
    • Amplifiers forum
  • Answered
  • INA168: Common Mode voltage not more than 60V

    Prashant Chavan6
    Prashant Chavan6
    Resolved
    Part Number: INA168 Other Parts Discussed in Thread: ISO1541 , TIDA-00313 , INA226 , TIDA-01608 , ISOW7842 , INA260 , OPA333 , TIDA-00528 , TIDA-00332 , INA138 , AMC1100 , AMC1200 , INA149-EP Hi All, URGENT!! I want High side current monitor, low…
    • Resolved
    • over 7 years ago
    • Amplifiers
    • Amplifiers forum
<>

Didn't find what you are looking for? Post a new question.

  • Ask a new question