• RE: INA592: 4-20mA current source

  

  Luis Chioye

  HI Shibin, As Kai has mentioned, on the current transmitter application, the main issue with the Howland Current source configuration is that could be sensitive to capacitive/inductive load and will likely become unstable while driving a long cable. There…

  • 2 months ago
  • Amplifiers
  • Amplifiers forum

• TIDA-00760: EVAL Kit

  

  shivakant dwivedi

  TI Thinks Resolved

  Part Number: TIDA-00760 Hi, I want to purchase eval board for TIDA-00760. Can you help in costing,time & from which vendor i will get it? Also tell as proper P/N for TIDA-00760.

  • over 4 years ago
  • Simulation, hardware & system design tools
  • Simulation, hardware & system design tools forum

• DAC8760: Spice model of DAC8760

  

  Zhen Luo18

  TI Thinks Resolved

  Part Number: DAC8760 Other Parts Discussed in Thread: TIDA-00760 , , DAC8411 , DAC8820 Hi, I was using TINA to simulate the performance of TIDA-00760 and evaluate the feasibilty of adding this design to my system. But I could not find the Spice model of…

  • over 2 years ago
  • Data converters
  • Data converters forum

• RE: DAC7571: How does a one-channel DAC output four signals?

  

  Joseph Wu

  Rengui, I don't know of a specific holding circuit, but you may be able to construct a basic sample and hold from a multiplexer and capacitors. There is a writeup for a design using the DAC8760 (not the DAC7571) for a similar function. It uses a single…

  • over 2 years ago
  • Data converters
  • Data converters forum
Answered

• RE: XTR117: XTR117

  

  Luis Chioye

  Resolved

  Hello Sandeep, It appears a number of the questions below are related to different circuits, each with their own different requirements, and these are no longer directly related to the original post of the XTR117 or the XTR111. You may need to open a new…

  • 10 months ago
  • Amplifiers
  • Amplifiers forum

• RE: DAC8775: Current consumption & isolation circuit

  

  Joseph Wu

  Mariem, Current consumption varies depending on how the device is used (and what channels are used for what). How many channels will be used for current output and for voltage output? What ranges will be used? If you post that information, I may be able…

  • over 2 years ago
  • Data converters
  • Data converters forum
Answered

• RE: [FAQ] Are there reference designs that can help me build a 4-20mA transmitter?

  

  Katlynne Jones

  Resolved

  To find reference designs leveraging the best in TI technology – from analog and power management to embedded processors, visit https://www.ti.com/reference-designs/index.html . All designs include a schematic, test data and design files. I will…

  • over 2 years ago
  • Amplifiers
  • Amplifiers forum

• RE: XTR111: Output current

  

  Iwata Etsuji

  Hi hechengwang , Honestly speaking, the appropriate value of the output cap for XTR111 is depending on the system requirements such as noise immunity, radiation noise, intrinsic safety, et cetera. While, you can also refer it to the subsection "DYNAMIC…

  • over 2 years ago
  • Amplifiers
  • Amplifiers forum

• RE: Multi-Channel Analog Output Module

  

  Tom Hendrick

  Hi Shivakant, I don't believe the TI Design for the Multi-Channel Analog Output (TIDA-00760) is readily available as an evaluation module.

  • over 4 years ago
  • Sensors
  • Sensors forum
Answered

• RE: ISO7741: Separating GND using the Isolation solution

  

  Koteshwar Rao

  Resolved

  Hi David, The primary reason for isolating in the digital domain is that it is relatively easy to isolate a digital signal and reproduce it accurately without any issues than an analog signal directly. Isolating an analog channel directly will pose many…

  • over 3 years ago
  • Isolation
  • Isolation forum

Didn't find what you are looking for? Post a new question.