Search tips
Showing 13,853 results View by: Thread Post Sort by

  • TIDM-HV-1PH-DCAC: TIDM-HV-1PH-DCAC: Current spikes at AC zero-crossing in grid connected inverter

    TI Thinks Resolved
    Part Number: TIDM-HV-1PH-DCAC Other Parts Discussed in Thread: PMP23338 Hi, We are currently working on a 2 kVA grid-tie inverter for telecom systems. We have developed and tested the inverter using a control technique similar to TIDM-HV-1PH-DCAC grid…

  • TIDM-CONNECTED-ETHERNET: ADC with Ethernet MCU requirement

    TI Thinks Resolved
    Part Number: TIDM-CONNECTED-ETHERNET Dear Ti, In one of the application we require 16Bit ADC which have atleast 100KSPS sampling rate per channel and Minimum channel required is 6. Also we need to transfer this adc result over ethernet in real time…

  • TIDM-1000: Load regulation on TIDM-1000 when connecting to a motor

    Part Number: TIDM-1000 Tool/software: I have been working with the TIDM-1000 3 phase vienna rectifier evaluation board, most recently in build 3 as per the reference design, with a C2000 microcontroller card. When connecting to a resistive load, the rectifier…

  • AM3352: Wifi Connection - Firmware upgrade failure (connected to ethernet)

    Part Number: AM3352 We are buiding application that connect to our webpage via ethernet interface where lighttpd is running and we are performing firmware upgrade which upload binary file and when we try to flash observed that we loosing the webpage activity…
    • Answered

  • MSP432E401Y: Establishing connections using Ethernet and PPP

    Resolved
    Part Number: MSP432E401Y I have a project using the Ethernet interface on the MSP432E401Y. Now I am trying to add support for a PPP connection over a modem. I have done a lot of reading online and have most of it working. I have ported the code from…
    • Resolved

  • TIDM-HV-1PH-DCAC: SFRA connection Problem

    TI Thinks Resolved
    Part Number: TIDM-HV-1PH-DCAC Other Parts Discussed in Thread: SFRA , C2000WARE , Tool/software: Hi, i have connection issue in running the SFRA. I have used the following (f280049c controller) #define SFRA_GUI_SCI_BASE SCIA_BASE #define SFRA_GUI_SCIRX_GPIO…

  • AM2434: Ethernet/IP connection timeout with multicast.

    Part Number: AM2434 Hello, I'm having issue with periodic timeouts when I set my Input only and Listen only connections as multicast. With point to point configuration I have no issue. Is there any specific operation I have to handle in assembly or…
    • Answered

  • AM2432: Ethernet/IP adapter suddenly closes connection

    Resolved
    Part Number: AM2432 Other Parts Discussed in Thread: SYSCONFIG Dear TI team, I have ported your Ethernet/IP adapter example to a softwareproject for our devices (based on AM2432, motor_control_sdk_am243x_09_02_00_12 ) . The connection can be established…
    • Resolved

  • DCA1000EVM: DCA1000EVM: Repeated failure - L4 component overheating and Ethernet connection failure

    Part Number: DCA1000EVM Other Parts Discussed in Thread: IWR6843AOP , AWR1642BOOST hi sorry for late reply for my last question. But i have same problem as last time. I am experiencing a severe and repeated hardware issue with the DCA1000EVM. Previously…
    • Answered

  • IWRL6432AOPEVM: Ethernet unable to connect

    Resolved
    Part Number: IWRL6432AOPEVM Other Parts Discussed in Thread: DCA1000EVM , Hello, I am currently trying to set up the IWRL6432AOPEVM with the DCA1000EVM in hopes of using the mmWave Studio GUI. Please see below for the switch settings on both devices…
    • Resolved

Didn't find what you are looking for? Post a new question.