Filter by Reset

All
Forums (11)
  • Amplifiers (8)
  • Data converters (1)
  • Power management (1)
  • Simulation, hardware & system... (1)
  • View all
Technical Articles (0)
Wikis (0)
Files (0)
Groups (0)
FAQ
  • Show only FAQs
Reply
  • Resolved
  • TI thinks resolved
  • Answer suggested
  • Has replies by TI employees
  • Has replies
Creation Date
  • Any
  • Past Week
  • Past Month
  • Past 3 Months
  • Past 6 Months
  • Past Year
From
To


Search tips
Showing 11 results View by: Thread Post Sort by
    Answered

  • TL061: TL061CDR Offset null function missing

    Resolved
    Part Number: TL061 Other Parts Discussed in Thread: TL071H Tool/software: Looking at the Data sheet for the TL061CDR which we have been buying for years, we have noticed that on page 4 of the August 2023 revision on figure 5-1 the TL061x diagram shows…
    • Resolved

  • TL061: Difference between TL061C and TL061I

    TI Thinks Resolved
    Part Number: TL061 Other Parts Discussed in Thread: TLC271 Dear Specialists, My customer'd like to know the difference between TL061C and TL061I. I would be grateful if you could advise. --- Currently, we are using TL061CPSR (SO package), but it is…

  • TPS65130: Dual supply for Filter.

    Part Number: TPS65130 Other Parts Discussed in Thread: TL061 , Tool/software: Hi, I am making LPF as per attached file. Sensor signal range is 2V to -1V ( BW 10 Hz) with DC 2.5V offset. I will need dual supply for op-amp TL061 otherwise I see clipping in…
    • Answered

  • RE: ADC102S021: Suitable ADC for low BW and low latency

    Resolved
    Dear Joel, Thanks for reply. There are two accelerometer so using two channel ADC. Another question I want to ask. I am also thinking to add Bessel filter with cutoff fc 25 HZ before ADC, as I am interested in Accelerometer data with up to only 10HZ. …

  • RE: TL081: TL031IP

    Hello Kadoyama-san, Regarding your questions, there is very limited information since these parts are older and the datasheet does not specify. I did however find the following thread: https://e2e.ti.com/support/amplifiers-group/amplifiers/f/amplifiers…

  • TL081: TL031IP

    Part Number: TL081 Other Parts Discussed in Thread: TL061 , TL031 , TLE2021 Hello PDIP(8) is used as a replacement for obsolete products. Initially, we considered TL081IP. but Regarding the Temperature coefficient of input offset, we calculated it from the…
    • Answered

  • LMP2011/TL061 input-referred current noise

    Resolved
    Other Parts Discussed in Thread: TL061 , LMP2011 , TL072 , LMP2021 Hi, My customer needs the following information. Could you show me the input--referred current noise of LMP2011 & TL061? Thanks and Regards, Kuramochi / Japan disty
    • Resolved
    • Answered

  • RE: TL031: Offset Adjustment

    Resolved
    Hi Kuramochi, as the TL031 is a "direct upgrade" for the TL061, you can do the offset adjustment like it's done with the TL061 :-) Kai
    • Answered

  • RE: Pspice for TI cannot find models and libraries

    Resolved
    Hi JC Sorry, I should have included this earlier. This is what I get in the session log when I try to run the simulation. INI File Location:C:\Users\Thomas\AppData\Roaming\SPB_Data\cdssetup\OrCAD_CaptureTIPSpice_Install/17.4.0/Capture.ini Processing TI…

  • RE: TINA-TI: newbie stupidity

    I am using a TL061 in another circuit at +12v and GND because I am measuring a 9 volt voltage with extremely low current (need the bifet 10E12 input impedance) is that supply voltage high enough for that use (single supply amp is used as a unity gain…
1 2

Didn't find what you are looking for? Post a new question.