• 

  Theodore Salmon

  • 11 months ago
  • Amplifiers
  • Amplifiers forum

  TL064: ST vs TI Parts

  • Resolved

  Part Number: TL064 Hello, I'm re-implementing a design revolving around a TL064 from STMicro
• 

  Paul Goedeke

  • over 1 year ago
  • Amplifiers
  • Amplifiers forum

  RE: TL064: Single Supply operation

  Hi Mark, The TL064 will work in single supply operation. You are correct that the input limitations will still apply; the input common mode range will be +4V to +17.6V in the case you presented. As long as the common mode range is within that range...
• 

  Kuramochi Tadahiko

  • over 2 years ago
  • Amplifiers
  • Amplifiers forum

  TL064: Output voltage > Input voltage on voltage follower

  • Resolved

  Part Number: TL064 Hi, The symptom that input signal is gained in spite of the voltage follower
• 

  Seishin

  • over 2 years ago
  • Amplifiers
  • Amplifiers forum

  TL064: Isink/Isource

  • Resolved

  Part Number: TL064 Hi, I would like to know the value of Isink and Isource of TL 064. What
• 

  kai klaas69

  • over 1 year ago
  • Amplifiers
  • Amplifiers forum

  RE: TL084: Why does my circuit oscillate with some 4MHz?

  Hi Roger, just wanted to simulate your circuit, but I'm unable to understand it. The schematic totally confuses me... :-) But I can say this: If I use the TL064/74/84 I always use phase lead caps in the feedback loop of OPAmps. 10...22pF is...
• 

  Bernhard Weller

  • over 5 years ago
  • Amplifiers
  • Amplifiers forum

  TL064: supply voltage missing min specification

  • Resolved

  Hello, a question regarding the minimum supply voltage came up, as there is no clear specification of it in the datasheet but on the product page there is. product page states: 7V minimum required total supply voltage but: in the datasheet there are graphs with respect to supply voltage, which go down...
• 

  Franck EUDARIC

  • over 5 years ago
  • Simulation, hardware & system design tools
  • Simulation, hardware & system design tools forum

  How to change the sections of an AOP in Tina

  • Resolved

  Hello, I'm looking how to change the differents sections of an AOP ( TL064 i.e.) in Ti-Tina? Thanks,
• 

  jay pandit

  • over 6 years ago
  • C2000™ microcontrollers
  • C2000™ microcontrollers forum

  RE: F28027 ADC: problem reading low

  Hi Devin, I am sensing the output of voltage sensor. In between the adc and voltage sensor I am using opamp TL064 in Voltage follower configuration. when the voltage is more than 1 volt ADC is reading voltage correctly. but for any voltage is...
• 

  KAUSHAL SHARMA

  • over 4 years ago
  • Power management
  • Power management forum

  TPS60403DBVR power issue

  Hello We are working on TPS60403 to generate -5V as per attached circuit. We have used this in two products as below: 1) The load is only to bias a single TL064 OPAMP, product layout is small (~90mmx80mm). Here the device works fine without any issues...
• 

  Angel Bellone

  • over 9 years ago
  • Amplifiers
  • Amplifiers forum

  Datasheet Tl064

  • Resolved

  En la figura 27 "IC Preamplifier" de dicha hoja de datos aparece un esquema usando el TL062. A primera vista aparentan estar invertidas las conexiones inversora y no inversora del operacional. Estoy en un error? Si es necesario traducir lo que expresé al inglés, lo haré. Saludos...

Didn't find what you are looking for? Post a new question.

• Ask a new question